P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTC P2120 (Click here).| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic). |
|
| DTC No. |
Data List |
| P2121 |
|
WIRING DIAGRAM
Refer to DTC P2120 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR) |
Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
- Standard:
Accelerator Pedal
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
Released
10 to 22%
24 to 40%
Depressed
52 to 90%
68 to 99%
Text in Illustration *1
Accelerator Pedal Assembly
*a
Depressed
*b
Released
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A13-1 (VCP2) - E30-4 (VCP2)
Always
Below 1 Ω
A13-2 (EPA2) - E30-3 (EPA2)
Always
Below 1 Ω
A13-3 (VPA2) - E31-1 (VPA2)
Always
Below 1 Ω
A13-4 (VCPA) - E30-6 (VCPA)
Always
Below 1 Ω
A13-5 (EPA) - E30-5 (EPA)
Always
Below 1 Ω
A13-6 (VPA) - E31-2 (VPA)
Always
Below 1 Ω
A13-1 (VCP2) or E30-4 (VCP2) - Body ground
Always
10 kΩ or higher
A13-3 (VPA2) or E31-1 (VPA2) - Body ground
Always
10 kΩ or higher
A13-4 (VCPA) or E30-6 (VCPA) - Body ground
Always
10 kΩ or higher
A13-6 (VPA) or E31-2 (VPA) - Body ground
Always
10 kΩ or higher
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2121) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P2121 is output
A
No DTC is output
B
|
|
||||
| A | |
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
