2014 Hilux · Service Manual HEATER & AIR CONDITIONING SYSTEM

23 Pressure Switch Circuit

Diagnostic trouble codes · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

E113418E14
The air conditioner pressure sensor turns off when the air conditioning refrigerant pressure extremely (0.196 MPa [2.0 kgf/cm2], 28 psi] or less) or extremely high (3.14 MPa [32.0 kgf/cm2, 455 psi] or more). When the air conditioning amplifier assembly detects the off state of the air conditioner pressure sensor, the air conditioning amplifier assembly outputs signals to the magnet clutch relay to turn the magnet clutch off.
DTC Code
DTC Detection Condition
Trouble Area
23
When either condition below is met:
  1. An open in pressure switch circuit
  2. Abnormal refrigerant pressure:
    1. 0.196 MPa (2.0 kgf/cm2, 28 psi) or less
    2. 3.14 MPa (32.0 kgf/cm2, 455 psi) or high
  1. Air conditioner tube & accessory assembly (air conditioner pressure sensor)
  2. Refrigerant and refrigerant pipe line
  3. Air conditioning amplifier assembly
  4. Harness or connector

WIRING DIAGRAM

E227736E02

INSPECTION PROCEDURE


1. CHECK REFRIGERANT PRESSURE
  1. Install a manifold gauge.

  1. Check refrigerant pressure (Click here).

    Standard Pressure:
    Pressure on high-pressure side
    1.37 to 1.57 MPa (13.9 to 16.0 kgf/cm2, 198 to 228 psi)

    HINT:
    If the refrigerant pressure is below 0.196 MPa (2.0 kgf/cm2, 28 psi), the refrigerant amount in the air conditioning cycle may have decreased significantly due to gas leakage or other problems.



NG
CHECK REFRIGERANT AND REFRIGERANT PIPE LINE
OK


2. CHECK AIR CONDITIONING OPERATION

  1. E225457E02
    Disconnect the P1 air conditioner pressure sensor connector.

  1. Using a service wire, connect terminals 1 and 2 of the connector on the vehicle wire harness side.

  1. Start the engine.

  1. Turn the A/C switch on and check the magnet clutch.

    OK:
    With terminals 1 and 2 connected, magnet clutch is on.
    With terminals 1 and 2 disconnected, magnet clutch is off.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioner Pressure Sensor)



NG
Go to step 3
OK

REPLACE AIR CONDITIONING TUBE & ACCESSORY ASSEMBLY (AIR CONDITIONER PRESSURE SENSOR)

3. CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER AND BODY GROUND)
  1. Disconnect the P1 air conditioner pressure sensor connector.

  1. Disconnect the A46 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-5 (PSW) - P1-2
    Always
    Below 1 Ω
    P1-1 - Body ground
    A46-5 (PSW) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table.)
    A
    OK (When troubleshooting according to DTC.)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← 23 Pressure Switch Circuit (Aug 2012 – Jul 2013)41 Air Mix Damper Control Servo Motor Circuit (Passenger Side) (Jun 2011 – Jul 2012) →