41 Air Mix Damper Control Servo Motor Circuit (Passenger Side)
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
The air mix damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the air mix control damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix control damper to any position. As a result, the air mix control damper varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air blowing toward the driver and front passenger side is as requested.- HINT:
- This DTC is also output if the damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| 41 |
The air mix control damper position does not change when the air conditioning amplifier assembly operates the air mix damper servo sub-assembly. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When DTC 41, 42 and 43 are output at same time, there would be malfunctioning on power source circuit (Click here).
| 1. PERFORM ACTUATOR CHECK |
Warm up the engine.
Enter actuator check mode (Click here).
Place your hand in front of a vent and check that the air mix control damper position changes (the temperature of the air changes) according to the display code.
Display Code
Air Mix Control Damper Position
0
COLD side (0% open)
1
COLD side (0% open)
2
COLD side (0% open)
3
COLD side (0% open)
4
COLD/HOT (50% open)
5
COLD/HOT (50% open)
6
HOT side (100% open)
7
HOT side (100% open)
8
HOT side (100% open)
9
HOT side (100% open)
- OK:
- Air mix control damper position changes in accordance with each display code.
- HINT:
- The progression through the steps of the actuator check can be changed from automatic to manual by pressing the front DEF switch.
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table.)
A
OK (When troubleshooting according to DTC.)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (AIR MIX DAMPER SERVO - AIR CONDITIONING AMPLIFIER) |
Disconnect the D17 air mix damper servo sub-assembly connector.
Disconnect the A44 and A46 air conditioning amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D17-5 (MHD) - A44-17 (AMH)
Always
Below 1 Ω
D17-4 (MCD) - A44-19 (AMC)
D17-3 (MHP) - A46-23 (PMB)
D17-2 (MCP) - A46-24 (PMA)
D17-1 (SG) - A46-20 (SG-1)
D17-1 (SG) - Body ground
Always
10 kΩ or higher
D17-2 (MCP) - Body ground
D17-3 (MHP) - Body ground
D17-4 (MCD) - Body ground
D17-5 (MHD) - Body ground
|
|
||||
| OK | |
| 3. REPLACE AIR MIX DAMPER SERVO SUB-ASSEMBLY |
Temporally replace the air mix damper servo sub-assembly with a new or normally functioning one (Click here).
Check the air mix control damper operates normally.
- OK:
- Air mix control damper operates normally.
|
|
||||
| OK | ||
| ||
