2014 Hilux · Service Manual HEATER & AIR CONDITIONING SYSTEM

42 Air Inlet Damper Control Servo Motor Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet control damper to any position, which controls the intake air settings.

HINT:
This DTC is also output if the air inlet control damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.

DTC Code
Detection Item
Trouble Area
42
The air inlet control damper position does not change when the air conditioning amplifier assembly operates the recirculation damper servo sub-assembly.
  1. Recirculation damper servo sub-assembly
  2. Harness or connector
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E227737E10

INSPECTION PROCEDURE

NOTICE:
When DTC 41, 42 and 43 are output at same time, there would be malfunctioning on power source circuit (Click here).


1. PERFORM ACTUATOR CHECK
  1. Remove the glove box to visually check the recirculation damper servo sub-assembly operation (Click here).

  1. Enter actuator check mode (Click here).

  1. Check that the air inlet control damper position changes according to the display code.

    Display Code
    Air Inlet Control Damper Position
    0
    Fresh
    1
    Fresh
    2
    Recirculation/fresh
    (50%)
    3
    Recirculation
    4
    Recirculation
    5
    Fresh
    6
    Fresh
    7
    Recirculation
    8
    Fresh
    9
    Fresh

    OK:
    Air inlet control damper position changes in accordance with each display code.

    HINT:
    The progression through the steps of the actuator check can be changed from automatic to manual by pressing the front DEF switch.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table.)
    A
    OK (When troubleshooting according to DTC.)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (RECIRCULATION DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the D15 recirculation damper servo sub-assembly connector.

  1. Disconnect the A44 and A46 air conditioning amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D15-4 - A44-22 (AIR)
    Always
    Below 1 Ω
    D15-5 - A44-23 (AIF)
    D15-2 - A46-17 (PIA)
    D15-3 - A46-16 (PIB)
    D15-1 - A46-21 (SG-7)
    D15-4 - Body ground
    Always
    10 kΩ or higher
    D15-5 - Body ground
    D15-2 - Body ground
    D15-3 - Body ground
    D15-1 - Body ground
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D15-5 - A44-22 (AIR)
    Always
    Below 1 Ω
    D15-4 - A44-23 (AIF)
    D15-2 - A46-17 (PIA)
    D15-3 - A46-16 (PIB)
    D15-1 - A46-21 (SG-7)
    D15-5 - Body ground
    Always
    10 kΩ or higher
    D15-4 - Body ground
    D15-2 - Body ground
    D15-3 - Body ground
    D15-1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
  1. Temporally replace the recirculation damper servo sub-assembly with a new or normally functioning one (Click here).

  1. Check the air inlet control damper operates normally.

    OK:
    Air inlet control damper operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (RECIRCULATION DAMPER SERVO IS DEFECTIVE)


← 41 Air Mix Damper Control Servo Motor Circuit (Passenger Side) (from Aug 2013)42 Air Inlet Damper Control Servo Motor Circuit (Aug 2012 – Jul 2013) →