INSTALLATION
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013
| 1. INSTALL CYLINDER PUSH ROD CLEVIS |
Install the lock nut and clevis to the push rod.
- HINT:
- Tighten the lock nut to the specified torque when adjusting the clutch pedal.
| 2. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY |
Install a new gasket and the clutch master cylinder assembly with the 2 nuts.
- Torque:
- 14 N*m{ 145 kgf*cm , 10 ft.*lbf }
Install the clutch pedal (Click here).
| 3. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE |
![]() ![]() |
Using a union nut wrench, connect the tube.
- Torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
| 4. CONNECT CLUTCH RESERVOIR TUBE |
![]() ![]() |
Connect the clutch reservoir hose with the clip to the clutch master cylinder.
- NOTICE:
- Connect the clutch reservoir hose so that it is not twisted.
| 5. INSTALL COMBINATION METER ASSEMBLY |
Install the combination meter assembly (Click here).
| 6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
| 7. BLEED AIR FROM CLUTCH PIPE LINE |
Fill the master cylinder reservoir with fluid.
Bleed air from the clutch system (Click here).
| 8. CHECK FOR CLUTCH FLUID LEAKAGE |
| 9. INSPECT AND ADJUST CLUTCH PEDAL ASSEMBLY |
Lift up the floor carpet to expose the asphalt sheet under the pedal.
Check that the pedal height is correct.

- Pedal height from dash panel:
- 179.9 to 189.9 mm (7.08 to 7.47 in.) (for LHD)
- 179.6 to 189.6 mm (7.07 to 7.46 in.) (for RHD)
w/o Clutch Switch:
Adjust the pedal height.Loosen the lock nut and turn the stopper bolt until the pedal height is within the specified range.
Tighten the lock nut.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
w/ Clutch Switch:
Adjust the pedal height.Loosen the lock nut of stopper bolt and clutch switch. Then turn clutch switch backward.
Turn the stopper bolt until the pedal height is within the specified range.
Tighten the lock nut of stopper bolt.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
Adjust the clutch switch assembly (Click here).
Check the pedal free play and push rod play.

- HINT:
- Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.
Depress the clutch pedal until resistance is felt.
Measure the distance between the pedal's released position and the position in the previous step.
- Standard pedal free play:
- 5.0 to 15.0 mm (0.197 to 0.591 in.)
Release the pedal. Using your finger, gently press the pedal until resistance increases slightly.
Measure the distance between the pedal's released position and the position in the previous step.
- Standard push rod play at pedal top:
- 1.0 to 5.0 mm (0.0394 to 0.197 in.)
Adjust the pedal free play and push rod play.
- HINT:
- The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.
Loosen the lock nut and turn the push rod until the pedal free play and push rod play are within the specified ranges.
- NOTICE:
- If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.
Tighten the lock nut.
- Torque:
- 12 N*m{ 120 kgf*cm , 9 ft.*lbf }
After adjusting the pedal free play and push rod play, check the pedal height.
Check the clutch release point.

Pull the parking brake lever and use wheel chocks to stabilize the vehicle.
Start the engine and run it at idle.
Without depressing the clutch pedal, slowly move the shift lever to R until the gears contact.
Gently depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.
- Standard distance A:
- 25 mm (0.984 in.) or more
- Check pedal height.
- Check push rod play and pedal free play.
- Bleed air from clutch line.
- Check clutch cover and disc.
| 10. CHECK FLUID LEVEL IN RESERVOIR |
- Fluid:
Made
Fluid
for TSAM Made
SAE J1704 or FMVSS No. 116 DOT 4
except TSAM Made
SAE J1703 or FMVSS No. 116 DOT 3


