2014 Hilux · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A118448E01
    Using SST and a press, press in a new bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A118449E01
    Align the claws of the bearing retainer with the grooves inside the drive end frame.

  1. Install the bearing retainer with the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor to the drive end frame.

    NOTICE:
    Do not drop the generator rotor.

  1. Install the generator drive end frame space collar to the generator rotor.

  1. Install the washer to the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A118450E01
    Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.

  1. A118451
    Install the generator coil assembly with the 4 through bolts.

    Torque:
    5.8 N*m{ 59 kgf*cm , 51 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A118452E01
    While pushing the 2 brushes inside the brush holder, insert a φ1.0 mm (0.039 in.) pin into the brush holder hole.

  1. A118453E01
    Install the brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the brush holder.


5. INSTALL TERMINAL INSULATOR

  1. A118454
    Install the terminal insulator.


6. INSTALL GENERATOR REAR END COVER

  1. A118436
    Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


7. INSTALL GENERATOR PULLEY
  1. Install the pulley to the rotor shaft by tightening the generator pulley nut by hand.

  1. A075664E06
    Install SST 1-A and B to the rotor shaft.
    SST
    09820-63011   (09820-06010, 09820-06021)
    Item
    Part No.
    SST 1-A and B
    09820-06010
    SST 2
    09820-06021

  1. Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise with the specified torque.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Make sure that the SST is secured to the rotor shaft.

  1. Mount the generator in a vise between aluminum plates.

  1. A203850E01
    Insert SST 2 to attach it to the pulley nut.

  1. A203821E01
    Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration.

    Torque:
    111 N*m{ 1127 kgf*cm , 81 ft.*lbf }

  1. Remove SST 2 from the generator.

  1. A075667E03
    Turn SST 1-A in the direction shown in the illustration, and remove SST 1-A and B.

  1. Turn the pulley, and check that the pulley moves smoothly.

← INSPECTION (from Jun 2011)INSTALLATION (Jun 2011 – Jul 2012) →