2014 Hilux · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Nov 2011

Versions by build date: Jun 2011 – Oct 2011 from Nov 2011


CHECK THEFT WARNING ECU ASSEMBLY (except 2 Step Unlock Function)
B119764E11
  1. Disconnect the T36 theft warning ECU assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T36-1 (E) - Body ground
    B-W - Body ground
    Ground
    Always
    Below 1 Ω
    T36-4 (+B1) - T36-1 (E)
    L-Y - B-W
    Battery power supply (power supply for ECU)
    Always
    11 to 14 V
    T36-14 (+B2) - T36-1 (E)
    G - B-W
    Battery power supply (for actuator operation)
    Always
    11 to 14 V
    T36-18 (IG) - T36-1 (E)
    R-L - B-W
    Ignition power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T36 theft warning ECU assembly connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T36-5 (KSW) - Body ground
    G-Y - Body ground
    Unlock warning switch input signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    T36-7 (CTY) - T36-1 (E)
    R-L - B-W
    All courtesy light switches input signal
    One or more doors open
    Below 1 V
    All doors closed
    11 to 14 V
    T36-9 (DSWH) - T36-1 (E)
    G-R - B-W
    Hood lock assembly (security courtesy switch) input signal
    Engine hood fully closed
    Below 1 Ω
    Engine hood open
    10 kΩ or higher
    T36-11 (HORN) - T36-1 (E)
    W-R - B-W
    Vehicle horns output signal
    Alarm sounding state
    Below 1 V
    Armed state
    11 to 14 V
    T36-13 (SH-) - T36-1 (E)
    B - B-W
    Security horn signal output
    Security horn is sounding
    (theft deterrent system is in alarm sounding state)
    Alternating between below 1 V and 11 to 14 V
    T36-27 (IND) - T36-1 (E)
    G-R - B-W
    Security indicator light assembly output signal
    Security indicator light is flashing
    (theft deterrent system is operating)
    Alternating between
    below 1 V and 11 to 14 V
    T36-28 (HAZD) - T36-1 (E)
    G-O - B-W
    All hazard warning light signals output
    Hazard warning lights are flashing
    (theft deterrent system is in alarm sounding state)
    Below 1 V
    1. If the result is not as specified, the theft warning ECU assembly may have a malfunction.


CHECK THEFT WARNING ECU ASSEMBLY (for 2 Step Unlock Function)
B119765E03
  1. Disconnect the T39 theft warning ECU assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T39-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    T39-3 (+B1) - T39-1 (E)
    L-Y - W-B
    Battery power supply (power supply for ECU)
    Always
    11 to 14 V
    T39-4 (IG) - T39-1 (E)
    R-L - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    T39-12 (+B2) - T39-1 (E)
    LG - W-B
    Battery power supply (for actuator operation)
    Always
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T39 theft warning ECU assembly connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T39-5 (KSW) - Body ground
    G-Y - Body ground
    Unlock warning switch input signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    T39-7 (CTY) - T39-1 (E)
    R-L - W-B
    All courtesy light switches input signal
    One or more doors open
    Below 1 V
    All doors closed
    11 to 14 V
    T39-9 (DSWH) - T39-1 (E)
    G-R - W-B
    Hood lock assembly (security courtesy switch) input signal
    Engine hood fully closed
    Below 1 Ω
    Engine hood open
    10 kΩ or higher
    T39-22 (IND) - T39-1 (E)
    G-R - W-B
    Security indicator light signal output
    Security indicator light is flashing
    (theft deterrent system is operating)
    Alternating between
    below 1 V and 11 to 14 V
    T39-23 (HAZD) - T39-1 (E)
    G-O - W-B
    All hazard warning light output signals
    Hazard warning lights are flashing
    (theft deterrent system is in alarm sounding state)
    Below 1 V
    T39-24 (HORN) - T39-1 (E)
    W-R - W-B
    Vehicle horns output signal
    Alarm sounding state
    Below 1 V
    Armed state
    11 to 14 V
    T39-26 (SH-) - T39-1 (E)
    B - W-B
    Security indicator light assembly output signal
    Security horn is sounding
    (theft deterrent system is in alarm sounding state)
    Alternating between below 1 V and 11 to 14 V
    1. If the result is not as specified, the theft warning ECU assembly may have a malfunction.

← TERMINALS OF ECU (Jun 2011 – Oct 2011)Engine Hood Courtesy Switch Circuit (from Jun 2011) →