14 Engine Coolant Temperature Communication Circuit
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
The engine coolant temperature sensor connected to the ECM detects the engine coolant temperature, which is used for warm up control when the engine is cold. The engine coolant temperature sensor sends a signal to the air conditioning amplifier assembly via the ECM.| DTC Code |
DTC Detection Condition |
Trouble Area |
| 14 |
An open or short in engine coolant temperature communication circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK ENGINE TYPE |
Check the engine type.
Result Result
Proceed to
Engine type: 1GR-FE
A
Engine type: 1KD-FTV
B
Engine type: 2KD-FTV
C
Engine type: 2TR-FE
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK FOR DTC (ENGINE CONTROL SYSTEM) |
Clear the DTCs (Click here).
Check the DTC (Click here).
Result Result
Proceed to
DTC (P0115, P0117 or P0118) is not output.
A
DTC (P0115, P0117 or P0118) is output.
B
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
Disconnect the A44 air conditioning amplifier assembly connector.
Disconnect the E13 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A44-8 (TW) - E13-14 (THWO)
Always
Below 1 Ω
A44-8 (TW) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table.)
A
OK (When troubleshooting according to DTC.)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. CHECK FOR DTC (ENGINE CONTROL SYSTEM) |
Clear the DTCs.
- for DPF: Click here.
- w/ EGR Cooler: Click here.
- w/o EGR Cooler: Click here.
- for DPF: Click here.
Check the DTC.
- for DPF: Click here.
- w/ EGR Cooler: Click here.
- w/o EGR Cooler: Click here.
Result Result
Proceed to
DTC (P0115, P0117 or P0118) is not output.
A
DTC (P0115, P0117 or P0118) is output. (for DPF)
B
DTC (P0115, P0117 or P0118) is output. (w/ EGR Cooler)
C
DTC (P0115, P0117 or P0118) is output. (w/o EGR Cooler)
D
- for DPF: Click here.
|
|
||||
|
|
||||
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
Disconnect the A44 air conditioning amplifier assembly connector.
Disconnect the E5 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A44-8 (TW) - E5-2 (THWO)
Always
Below 1 Ω
A44-8 (TW) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table.)
A
OK (When troubleshooting according to DTC.)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 6. CHECK FOR DTC (ENGINE CONTROL SYSTEM) |
Clear the DTCs.
- for DPF: Click here.
- w/ EGR Cooler: Click here.
- w/o EGR Cooler: Click here.
- for DPF: Click here.
Check the DTC.
- for DPF: Click here.
- w/ EGR Cooler: Click here.
- w/o EGR Cooler: Click here.
Result Result
Proceed to
DTC (P0115, P0117 or P0118) is not output.
A
DTC (P0115, P0117 or P0118) is output. (for DPF)
B
DTC (P0115, P0117 or P0118) is output. (w/ EGR Cooler)
C
DTC (P0115, P0117 or P0118) is output. (w/o EGR Cooler)
D
- for DPF: Click here.
|
|
||||
|
|
||||
|
|
||||
| A | |
| 7. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
Disconnect the A44 air conditioning amplifier assembly connector.
Disconnect the E5 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A44-8 (TW) - E5-2 (THWO)
Always
Below 1 Ω
A44-8 (TW) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table.)
A
OK (When troubleshooting according to DTC.)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 8. CHECK FOR DTC (ENGINE CONTROL SYSTEM) |
Clear the DTCs (Click here).
Check the DTC (Click here).
Result Result
Proceed to
DTC (P0115, P0117 or P0118) is not output.
A
DTC (P0115, P0117 or P0118) is output.
B
|
|
||||
| A | |
| 9. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
Disconnect the A44 air conditioning amplifier assembly connector.
Disconnect the E10 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A44-8 (TW) - E10-14 (THWO)
Always
Below 1 Ω
A44-8 (TW) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table.)
A
OK (When troubleshooting according to DTC.)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
