2014 Hilux · Service Manual ENGINE

15 (4) Throttle Motor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The fully open position of the throttle valve is detected by the throttle open switch mounted on the venturi.
If this DTC is stored, the ECM shuts down the power for the throttle control motor.
DTC No.
DTC Detection Condition
Trouble Area
15 (4)
Open or short in throttle control motor circuit
  1. Open or short in throttle control motor circuit
  2. Throttle control motor
  3. Throttle valve
  4. Open or short in throttle open switch circuit
  5. Throttle open switch
  6. ECM
Open or short in throttle open switch circuit

WIRING DIAGRAM

A261025E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. INSPECT THROTTLE OPEN SWITCH

  1. A106810
    Disconnect the throttle open switch connector.

  1. Remove the venturi.

  1. Measure the resistance of the throttle open switch.

    Standard resistance:
    Tester Connection
    Throttle Valve Condition
    Specified Condition
    1 - 2
    Open
    Below 1 Ω
    1 - 2
    Closed
    10 kΩ or higher

    HINT:
    The throttle open switch is integrated with the venturi. If the throttle open switch needs to be replaced, the entire venturi must be replaced.



NG
REPLACE VENTURI
OK


2. CHECK WIRE HARNESS (THROTTLE OPEN SWITCH - ECM AND BODY GROUND)

  1. A110563E03
    Disconnect the T28 throttle open switch connector.

  1. Disconnect the E22 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T28-1 - Body ground
    Below 1 Ω
    E22-15 (THOP) - T28-2
    Below 1 Ω
    E22-15 (THOP) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK ECM (THROTTLE CONTROL MOTOR CIRCUIT)

  1. A106827E04
    During engine racing, measure the waveform according to the value(s) in the table below.

    OK:
    Tester Connection
    Specified Condition
    E23-10 (LU+A) - E23-13 (E01)
    Correct waveform is as shown
    E23-9 (LU-A) - E23-13 (E01)
    Correct waveform is as shown
    E23-8 (LU+B) - E23-13 (E01)
    Correct waveform is as shown
    E23-7 (LU-B) - E23-13 (E01)
    Correct waveform is as shown



OK
REPLACE ECM
NG


4. INSPECT THROTTLE CONTROL MOTOR

  1. A031135E03
    Disconnect the throttle control motor connector.

  1. Measure the resistance of the throttle control motor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    18 to 22 Ω
    2 - 3
    20°C (68°F)
    18 to 22 Ω
    4 - 5
    20°C (68°F)
    18 to 22 Ω
    5 - 6
    20°C (68°F)
    18 to 22 Ω

    HINT:
    The throttle control motor is integrated with the venturi. If the throttle control motor needs to be replaced, the entire venturi must be replaced.



NG
REPLACE VENTURI
OK


5. CHECK WIRE HARNESS (THROTTLE CONTROL MOTOR - ECM)

  1. A106828E03
    Disconnect the throttle control motor connector.

  1. Disconnect the E23 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T25-6 - E23-10 (LU+A)
    Below 1 Ω
    T25-4 - E23-9 (LU-A)
    Below 1 Ω
    T25-3 - E23-8 (LU+B)
    Below 1 Ω
    T25-1 - E23-7 (LU-B)
    Below 1 Ω
    E23-10 (LU+A) - E23-13 (E01)
    10 kΩ or higher
    E23-9 (LU-A) - E23-13 (E01)
    10 kΩ or higher
    E23-8 (LU+B) - E23-13 (E01)
    10 kΩ or higher
    E23-7 (LU-B) - E23-13 (E01)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT


← 14 (4) Timing Control System Malfunction (from Jun 2011)17 (1) Interior IC Malfunction (Jun 2011 – Oct 2011) →