2014 Hilux · Service Manual ENGINE

U0101 Lost Communication with TCM

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM (engine control unit) intercommunicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).
If there is a problem in this intercommunication, the ECM sets a DTC.
DTC No.
DTC Detection Condition
Trouble Area
U0101
  1. Following conditions are met for 1.25 seconds (1 trip detection logic):
    1. Ignition switch ON
    2. Battery voltage is 10.5 V or more
    3. No intercommunication between ECM and TCM
  1. ECM
  2. TCM
  3. ECM to TCM circuit

WIRING DIAGRAM

A159341E08

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    U0101
    A
    U0101 and other DTCs
    B

    HINT:
    If any DTCs other than U0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT TCM

  1. G037243E10
    Disconnect the T38 TCM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    BATT (T38-5) - Body ground
    11 to 14 V

  1. F045523E33
    Disconnect the T19 TCM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E1 (T19-1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - TCM)

  1. G034917E13
    Disconnect the E6 ECM connector.

  1. Disconnect the T38 TCM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    CAN+ (E6-22) - CAN+ (T38-21)
    Below 1 Ω
    CAN- (E6-21) - CAN- (T38-20)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    CAN+ (E6-22) or CAN+ (T38-21) - Body ground
    10 kΩ or higher
    CAN- (E6-21) or CAN- (T38-20) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    No output
    A
    U0101
    B



B
REPLACE TCM
A

END


← P2563 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance (+ P2564, P2565, P2588, P2589) (from Aug 2014)U0101 Lost Communication with TCM (Aug 2012 – Jul 2013) →