2014 Hilux · Service Manual ENGINE

P0105 Manifold Absolute Pressure / Barometric Pressure Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

A006532E03
The manifold absolute pressure sensor detects the intake manifold pressure by using the built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)). As a result, the ECM controls the air-fuel ratio at the proper level under any driving conditions, and is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.
DTC No.
DTC Detection Condition
Trouble Area
P0105
P0107
P0108
Open or short in manifold absolute pressure sensor circuit for
0.5 seconds or more
(1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. Turbocharger assembly
  4. ECM

WIRING DIAGRAM

A154582E02

INSPECTION PROCEDURE

HINT:
  1. If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).


1. READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / MAP.

  1. Read the values.

    Standard:
    Same value as the actual atmospheric pressure.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. CHECK ECM (VC VOLTAGE)
A066060E31
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E8-18 (VC) - E8-28 (E2)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


3. CHECK ECM (PIM VOLTAGE)
A066060E32
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-28 (PIM) - E8-28 (E2)
    Applied negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
    1.1 to 1.7 V
    E7-28 (PIM) - E8-28 (E2)
    Same as atmospheric pressure
    2.0 to 2.6 V
    E7-28 (PIM) - E8-28 (E2)
    Applied positive pressure of 170 kPa (1,275 mmHg, 50.2 in.Hg)
    3.0 to 3.6 V



OK
REPLACE ECM (Click here)
NG


4. CHECK WIRE HARNESS (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
A099844E21
  1. Disconnect the T9 sensor connector.

  1. Disconnect the E7 and E8 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T9-2 (PIM) - E7-28 (PIM)
    Below 1 Ω
    T9-3 (VC) - E8-18 (VC)
    Below 1 Ω
    T9-1 (E) - E8-28 (E2)
    Below 1 Ω
    T9-2 (PIM) or E7-28 (PIM) - Body ground
    10 kΩ higher
    T9-3 (VC) or E8-18 (VC) - Body ground
    10 kΩ higher
    T9-1 (E) or E8-28 (E2) - Body ground
    10 kΩ higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. INSPECT TURBOCHARGER SUB-ASSEMBLY

OK:
None of the inspection results show any abnormalities.



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY
OK


6. INSPECT EGR VALVE ASSEMBLY*

HINT:
*: w/ EGR valve only.

OK:
None of the inspection results show any abnormalities.



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR


← P0105 Manifold Absolute Pressure / Barometric Pressure Circuit (+ P0107, P0108) (Aug 2013 – Jul 2014)P0110 Intake Air Temperature Circuit (+ P0112, P0113) (Jun 2011 – Jul 2012) →