Home › ENGINE › 2KD-FTV EMISSION CONTROL › EGR VALVE (w/o EGR Cooler)
REMOVAL
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
1.
PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here ).
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
3.
REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here )
4.
REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/ Intercooler)
NOTICE:
After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
w/ Intercooler:
Remove the 2 nuts and No. 3 injection pipe clamp.
Remove the 2 bolts and 2 No. 2 injection pipe clamps.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
Text in Illustration
*a
Injector Side
*b
Common Rail Side
w/o Intercooler:
Remove the bolt and No. 2 injection pipe clamp.
Text in Illustration
*1
No. 2 Injection Pipe Clamp
*2
No. 3 Injection Pipe Clamp
*a
Injector Side
*b
Common Rail Side
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
5.
REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET
Remove the 3 bolts and No. 2 intake air connector bracket.
Text in Illustration
*A
w/ Intercooler
*B
w/o Intercooler
*1
No. 2 Intake Air Connector Bracket
*2
Intake Air Connector
6.
REMOVE INTAKE AIR CONNECTOR (w/o Intercooler)
Remove the 2 nuts, bolt, intake air connector and gasket.
7.
REMOVE NO. 3 WATER BY-PASS PIPE (w/ Intercooler)
Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with the wire harness.
8.
REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR)
w/ Intercooler:
Disconnect the 2 connectors.
Disconnect the 6 vacuum hoses.
Remove the bolt and No. 1 gas filter with gas filter bracket.
Remove the 2 bolts and electric vacuum regulating valve.
w/o Intercooler:
Disconnect the connector.
Disconnect the 2 vacuum hoses.
Remove the 2 bolts and electric vacuum regulating valve together with the bracket.
NOTICE:
Do not remove the electric vacuum regulating valve from the bracket.
9.
REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ Intercooler)
Remove the 3 nuts, No. 2 intake air connector and gasket.
10.
REMOVE INTAKE AIR CONNECTOR (w/ Intercooler)
Remove the 3 bolts, intake air connector and 2 gaskets.
11.
REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY (w/ Intercooler)
Remove the 2 nuts, electric EGR control valve with No. 1 EGR pipe and gasket.
12.
REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
w/ Intercooler: Remove the 2 bolts, No. 1 EGR pipe and gasket from the EGR valve adapter.
w/o Intercooler: Remove the 2 bolts, 2 nuts, No. 1 EGR pipe and 2 gaskets.
Text in Illustration
*1
Gasket
13.
REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
w/ Intercooler: Remove the 2 bolts, electric EGR control valve and gasket from the EGR valve adapter.
w/o Intercooler:
Disconnect the EGR valve position sensor connector.
Remove the electric EGR control valve and gasket.