2014 Hilux · Service Manual BRAKE

C1232 Acceleration Sensor Stuck Malfunction

Diagnostic trouble codes · Vehicles built Jun 2011 – Oct 2011

Also covers:

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate assembly via the CAN communication system.
The yaw rate sensor assembly has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.
DTC C1232, C1243, C1245 and C1279 are also stored when calibration has not been completed.
DTC C1279 can be cleared when the yaw rate sensor assembly sends a yaw rate and/or acceleration signal or Test Mode ends. DTC C1279 is stored only in Test Mode.
DTC Code
DTC Detection Condition
Trouble Area
C1232
At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
  1. Acceleration sensor (Yaw rate sensor assembly)
  2. Yaw rate sensor assembly circuit
C1243
While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change by 0.0294 G or more occurs 16 times or more.
  1. Acceleration sensor (Yaw rate sensor assembly)
  2. Yaw rate sensor assembly circuit
C1245
At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
  1. Acceleration sensor (Yaw rate sensor assembly)
  2. Yaw rate sensor assembly circuit
  3. Sensor installation
C1279
Stored during Test Mode.
  1. Acceleration sensor (Yaw rate sensor assembly)
  2. Sensor installation

WIRING DIAGRAM

C185399E23

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the yaw rate sensor assembly, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

HINT:
When DTC U0123 and/or U0124 is output together with DTC C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0123 and/or U0124 first (Click here).


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel and decelerate (depress the brake pedal) the vehicle.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).

  1. Check if DTCs for zero point calibration of the yaw rate sensor (C1210) or for zero point calibration of the acceleration sensor (C1336) are output (Click here).

    Result 
    Result
    Proceed to
    DTC relating to yaw rate and acceleration sensor is output
    A
    DTC relating to CAN communication system is output
    B
    DTC C1210 and/or C1336 is output
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2. CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate sensor assembly is installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not installed at an angle.



NG
INSTALL YAW RATE SENSOR ASSEMBLY CORRECTLY (Click here)
OK


3. CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the yaw rate sensor assembly connector.

  1. C208309E24
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Y1-1 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)


← C1210 Zero Point Calibration of Yaw Rate Sensor Undone (+ C1336) (from Aug 2014)C1232 Acceleration Sensor Stuck Malfunction (+ C1243, C1245, C1279) (Nov 2011 – Mar 2012) →