2014 Hilux · Service Manual BRAKE

C1381 Acceleration Sensor Power Supply Voltage Malfunction

Diagnostic trouble codes · Vehicles built Nov 2011 – Mar 2012

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor assembly via the CAN communication system.
The yaw rate sensor assembly has a built-in acceleration sensor.
If there is trouble in the bus lines between the yaw rate sensor and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.
DTC C1381 is also stored when calibration has not been completed.
DTC Code
DTC Detection Condition
Trouble Area
C1381
At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
  1. ECU-IG&GAUGE fuse
  2. Acceleration sensor (Yaw rate sensor assembly)
  3. Yaw rate sensor assembly power source circuit

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the yaw rate sensor assembly, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK TERMINAL VOLTAGE (IG TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the yaw rate sensor assembly connector.

  1. C208309E25
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (GND TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Y1-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 3 km/h (2 mph) or more for at least 10 seconds or more.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).



B
REPLACE YAW RATE SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1381 Acceleration Sensor Power Supply Voltage Malfunction (Jun 2011 – Oct 2011)C1381 Acceleration Sensor Power Supply Voltage Malfunction (Apr 2012 – Jul 2012) →