2014 Hilux · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The radio and display receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM

C240170E33

INSPECTION PROCEDURE


1. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


2. CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the speaker with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the speaker connectors to the speakers.
    2. When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction does not disappear
    A
    Malfunction disappears
    B



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
A


4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 2 SPEAKER)
  1. Disconnect the R23 radio and display receiver assembly connector.

  1. Disconnect the T24*1 and/or T23*2 speaker connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    R23-1 (FR+) - T24-4
    Always
    Below 1 Ω
    R23-5 (FR-) - T24-2
    R23-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R23-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    R23-2 (FL+) - T23-4
    Always
    Below 1 Ω
    R23-6 (FL-) - T23-2
    R23-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R23-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E178457
    Disconnect the S16*1 and/or S15*2 speaker connector.
    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the T24*1 and/or T23*2 speaker connector.

  1. Disconnect the S16*1 and/or S15*2 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T24-3 (+) - S16-1
    Always
    Below 1 Ω
    T24-1 (-) - S16-2
    T24-3 (+) - Body ground
    Always
    10 kΩ or higher
    T24-1 (-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T23-3 (+) - S15-1
    Always
    Below 1 Ω
    T23-1 (-) - S15-2
    T23-3 (+) - Body ground
    Always
    10 kΩ or higher
    T23-1 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

7. INSPECT REAR SPEAKER ASSEMBLY

  1. E178457
    for Extra Cab:
    1. Disconnect the S20*1 and/or S19*2 speaker connector.

      1. *1: for RH
      2. *2: for LH

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Always
      4 Ω

  1. for Double Cab:

    1. Disconnect the S18*1 and/or S17*2 speaker connector.

      1. *1: for RH
      2. *2: for LH

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Always
      4 Ω



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER)
  1. for Extra Cab:

    1. Disconnect the R22 radio and display receiver assembly connector.

    2. Disconnect the S20*1 and/or S19*2 speaker connector.

      1. *1: for RH
      2. *2: for LH

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RH 
      Tester Connection
      Condition
      Specified Condition
      R22-1 (RR+) - S20-1
      Always
      Below 1 Ω
      R22-3 (RR-) - S20-2
      R22-1 (RR+) - Body ground
      Always
      10 kΩ or higher
      R22-3 (RR-) - Body ground
      for LH 
      Tester Connection
      Condition
      Specified Condition
      R22-2 (RL+) - S19-1
      Always
      Below 1 Ω
      R22-6 (RL-) - S19-2
      R22-2 (RL+) - Body ground
      Always
      10 kΩ or higher
      R22-6 (RL-) - Body ground

  1. for Double Cab:

    1. Disconnect the R22 radio and display receiver assembly connector.

    2. Disconnect the S18*1 and/or S17*2 speaker connector.

      1. *1: for RH
      2. *2: for LH

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RH 
      Tester Connection
      Condition
      Specified Condition
      R22-1 (RR+) - S18-1
      Always
      Below 1 Ω
      R22-3 (RR-) - S18-2
      R22-1 (RR+) - Body ground
      Always
      10 kΩ or higher
      R22-3 (RR-) - Body ground
      for LH 
      Tester Connection
      Condition
      Specified Condition
      R22-2 (RL+) - S17-1
      Always
      Below 1 Ω
      R22-6 (RL-) - S17-2
      R22-2 (RL+) - Body ground
      Always
      10 kΩ or higher
      R22-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)


← Speaker Circuit (Jun 2011 – Jul 2012)Speaker Circuit (from Aug 2013) →