2014 Hilux · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The radio and display receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM

E285155E01

INSPECTION PROCEDURE

HINT:
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for T-Connect.


1. CHECK SPEAKER (OPERATION CHECK)

  1. E273721
    Enter the "System Check Mode" screen. [Refer to Check SP Check On in Operation Check (Click here)]

  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the R23 radio and display receiver assembly connector.

  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

  1. for 6 Speakers:Disconnect the T24*1 and/or T23*2 front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side (for 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-1 (FR+) - T24-4
    Always
    Below 1 Ω
    R23-5 (FR-) - T24-2
    Always
    Below 1 Ω
    T24-3 - S16-1
    Always
    Below 1 Ω
    T24-1 - S16-2
    Always
    Below 1 Ω
    R23-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R23-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1 - Body ground
    Always
    10 kΩ or higher
    for LH Side (for 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-2 (FL+) - T23-4
    Always
    Below 1 Ω
    R23-6 (FL-) - T23-2
    Always
    Below 1 Ω
    T23-3 - S15-1
    Always
    Below 1 Ω
    T23-1 - S15-2
    Always
    Below 1 Ω
    R23-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R23-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    T23-3 - Body ground
    Always
    10 kΩ or higher
    T23-1 - Body ground
    Always
    10 kΩ or higher
    for RH Side (except 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-1 (FR+) - S16-1
    Always
    Below 1 Ω
    R23-5 (FR-) - S16-2
    Always
    Below 1 Ω
    R23-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R23-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH Side (except 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-2 (FL+) - S15-1
    Always
    Below 1 Ω
    R23-6 (FL-) - S15-2
    Always
    Below 1 Ω
    R23-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R23-6 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

    1. *1: for RH Side
    2. *2: for LH Side

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4. CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

5. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the R22 radio and display receiver assembly connector.

  1. for Double Cab:

    1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

  1. for Extra Cab:

    1. Disconnect the S20*1 and/or S19*2 rear speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab RH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R22-3 (RR-) - S18-2
    Always
    Below 1 Ω
    R22-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R22-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for Double Cab LH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R22-6 (RL-) - S17-2
    Always
    Below 1 Ω
    R22-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R22-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    for Extra Cab RH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-1 (RR+) - S20-1
    Always
    Below 1 Ω
    R22-3 (RR-) - S20-2
    Always
    Below 1 Ω
    R22-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R22-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    except Extra Cab LH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-2 (RL+) - S19-1
    Always
    Below 1 Ω
    R22-6 (RL-) - S19-2
    Always
    Below 1 Ω
    R22-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R22-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT REAR SPEAKER ASSEMBLY
  1. *1: for RH Side
  2. *2: for LH Side
  1. for Double Cab:

    1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

  1. for Extra Cab:

    1. Disconnect the S20*1 and/or S19*2 rear speaker assembly connector.

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)


← Speaker Circuit (Aug 2012 – Jul 2013)Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter (Jun 2011 – Jul 2012) →