Speaker Circuit
Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
The radio receiver assembly sends sound signals to the speakers.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK SPEAKER |
 |
Check the malfunctioning speakers.
Result
Result
|
Proceed to
|
Malfunction in front speaker area (for 6 Speakers)
|
A
|
Malfunction in front speaker area (except 6 Speakers)
|
B
|
Malfunction in rear speaker area (except 2 Speakers)
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
|
|
| A |
|
 |
|
| 2. CHECK FRONT SIDE SPEAKER |
 |
Check the malfunctioning speakers.
Result
Result
|
Proceed to
|
Front No. 2 speaker assembly
|
A
|
Front No. 1 speaker assembly
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
 |
Temporarily replace the speaker with a new or normally functioning one (Click here).
Check that the malfunction disappears.
- HINT:
- Connect all the speaker connectors to the speakers.
- When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.
Result
Result
|
Proceed to
|
Malfunction does not disappear
|
A
|
Malfunction disappears
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER) |
 |
Disconnect the R1 radio receiver assembly connector.
Disconnect the T24*1 and/or T23*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH
Tester Connection
|
Condition
|
Specified Condition
|
R1-1 (FR+) - T24-4
|
Always
|
Below 1 Ω
|
R1-5 (FR-) - T24-2
|
R1-1 (FR+) - Body ground
|
Always
|
10 kΩ or higher
|
R1-5 (FR-) - Body ground
|
for LH
Tester Connection
|
Condition
|
Specified Condition
|
R1-2 (FL+) - T23-4
|
Always
|
Below 1 Ω
|
R1-6 (FL-) - T23-2
|
R1-2 (FL+) - Body ground
|
Always
|
10 kΩ or higher
|
R1-6 (FL-) - Body ground
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|
| 5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
 |
- Disconnect the S16*1 and/or S15*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Always
|
4 Ω
|
Result
Result
|
Proceed to
|
OK (for 6 Speakers)
|
A
|
OK (except 6 Speakers)
|
B
|
NG
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
|
|
| A |
|
 |
|
| 6. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER) |
 |
- *1: for RH
- *2: for LH
Disconnect the T24*1 and/or T23*2 speaker connector.
Disconnect the S16*1 and/or S15*2 speaker connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH
Tester Connection
|
Condition
|
Specified Condition
|
T24-3 (+) - S16-1
|
Always
|
Below 1 Ω
|
T24-1 (-) - S16-2
|
T24-3 (+) - Body ground
|
Always
|
10 kΩ or higher
|
T24-1 (-) - Body ground
|
for LH
Tester Connection
|
Condition
|
Specified Condition
|
T23-3 (+) - S15-1
|
Always
|
Below 1 Ω
|
T23-1 (-) - S15-2
|
T23-3 (+) - Body ground
|
Always
|
10 kΩ or higher
|
T23-1 (-) - Body ground
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|
| 7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER) |
 |
Disconnect the R1 radio receiver assembly connector.
Disconnect the S16*1 and/or S15*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH
Tester Connection
|
Condition
|
Specified Condition
|
R1-1 (FR+) - S16-1
|
Always
|
Below 1 Ω
|
R1-5 (FR-) - S16-2
|
R1-1 (FR+) - Body ground
|
Always
|
10 kΩ or higher
|
R1-5 (FR-) - Body ground
|
for LH
Tester Connection
|
Condition
|
Specified Condition
|
R1-2 (FL+) - S15-1
|
Always
|
Below 1 Ω
|
R1-6 (FL-) - S15-2
|
R1-2 (FL+) - Body ground
|
Always
|
10 kΩ or higher
|
R1-6 (FL-) - Body ground
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|
| 8. INSPECT REAR SPEAKER ASSEMBLY |
 |
- for Extra Cab:
Disconnect the S20*1 and/or S19*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Always
|
4 Ω
|
for Double Cab:
Disconnect the S18*1 and/or S17*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
1 - 2
|
Always
|
4 Ω
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 9. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER) |
 |
for Extra Cab:
Disconnect the R2 radio receiver assembly connector.
Disconnect the S20*1 and/or S19*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH
Tester Connection
|
Condition
|
Specified Condition
|
R2-1 (RR+) - S20-1
|
Always
|
Below 1 Ω
|
R2-3 (RR-) - S20-2
|
R2-1 (RR+) - Body ground
|
Always
|
10 kΩ or higher
|
R2-3 (RR-) - Body ground
|
for LH
Tester Connection
|
Condition
|
Specified Condition
|
R2-2 (RL+) - S19-1
|
Always
|
Below 1 Ω
|
R2-6 (RL-) - S19-2
|
R2-2 (RL+) - Body ground
|
Always
|
10 kΩ or higher
|
R2-6 (RL-) - Body ground
|
for Double Cab:
Disconnect the R2 radio receiver assembly connector.
Disconnect the S18*1 and/or S17*2 speaker connector.
- *1: for RH
- *2: for LH
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH
Tester Connection
|
Condition
|
Specified Condition
|
R2-1 (RR+) - S18-1
|
Always
|
Below 1 Ω
|
R2-3 (RR-) - S18-2
|
R2-1 (RR+) - Body ground
|
Always
|
10 kΩ or higher
|
R2-3 (RR-) - Body ground
|
for LH
Tester Connection
|
Condition
|
Specified Condition
|
R2-2 (RL+) - S17-1
|
Always
|
Below 1 Ω
|
R2-6 (RL-) - S17-2
|
R2-2 (RL+) - Body ground
|
Always
|
10 kΩ or higher
|
R2-6 (RL-) - Body ground
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|