P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.The ECM outputs a signal to the turbo motor driver, which actuates the DC motor, to control the nozzle vane position.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0046 |
Either of following conditions met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0046) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0046
A
P0046 and other DTCs
B
- HINT:
- If any DTCs other than P0046 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION) |
Turn the ignition switch ON.
Turn the ignition switch OFF and check the DC motor operation.
- OK:
- When ignition switch is turned OFF, operation link moves as shown in A through D in illustration below.
- Operation link and motor rod move smoothly when moving from position shown in A to that shown in B, and from position shown in B to that shown in C.


|
|
||||
| OK | ||
| ||
| 3. INSPECT TURBO MOTOR DRIVER |
Voltage Inspection
Turn the ignition switch ON (IG).

Measure the voltage between the terminals of the turbo motor driver connector.
- Standard voltage:
Tester Connection
Specified Condition
+B (T8-3) - GND (T8-4)
11 to 14 V
Output Waveform Inspection
Turn the ignition switch ON (IG).

Check the waveform of the ECM connectors using an oscilloscope.
- OK:
Tester Connection
Condition
Specified Condition
VNTI (T8-2) - GND (T8-4)
Ignition switch ON
Correct waveform is as shown
|
|
||||
| OK | |
| 4. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE) |
Disconnect the T10 DC motor connector.

Measure the resistance of the DC motor.
- Standard resistance:
Tester Connection
Specified Condition
M+ (2) - M- (1)
1 to 100 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER) |
Disconnect the T10 DC motor connector.

Disconnect the T8 turbo motor drive connector.
Measure the resistance of the wire harness side connector.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
M+ (T8-12) - M+ (T10-2)
Below 1 Ω
M- (T8-5) - M- (T10-1)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
M+ (T8-12) or M+ (T10-2) - Body ground
10 kΩ or higher
M- (T8-5) or M- (T10-1) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK IF DTC OUTPUT RECURS (DTC P0046) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear the DTC (Click here).
Start the engine.
Perform the test drive.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0046
A
No output
B
|
|
||||
| A | ||
| ||
