2014 Hilux · Service Manual ENGINE

P2009 Intake Manifold Runner Control Circuit Low (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P2006 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2009
Open in VSV for swirl control valve circuit for 0.5 seconds
(2 trip detection logic)
  1. VSV for swirl control valve
  2. Open in VSV for swirl control valve circuit
  3. ECM
P2010
Short in VSV for swirl control valve circuit for 0.5 seconds
(2 trip detection logic)
  1. VSV for swirl control valve
  2. Short in VSV for swirl control valve circuit
  3. ECM

WIRING DIAGRAM

Refer to DTC P2006 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
A067588E05
  1. Connect the intelligent tester to the DLC3.

  1. Disconnect the vacuum hoses from the VSV for swirl control valve.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

  1. Check the VSV operation when it is operated using the intelligent tester.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


2. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)

  1. G036521E11
    Disconnect the S9 VSV for swirl control valve connector.

  1. Measure the resistance of the VSV for swirl control valve.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    33 to 39 Ω



NG
REPLACE VACUUM CONTROL VALVE SET
OK


3. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (POWER SOURCE VOLTAGE)

  1. A154589E24
    Disconnect the S9 VSV for swirl control valve connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    S9-2 - Body ground
    11 to 14 V



OK
Go to step 5
NG


4. CHECK HARNESS AND CONNECTOR (VSV FOR SWIRL CONTROL VALVE - NO. 1 INTEGRATION RELAY)
G034915E18
  1. Remove the No. 1 integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J No. 1 integration relay connector.

  1. Disconnect the S9 VSV for swirl control valve connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    1J-5 - S9-2
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    1J-5 or S9-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

INSPECT ECM POWER SOURCE CIRCUIT (Click here)

5. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE - ECM)

  1. A149634E13
    Disconnect the S9 VSV for swirl control valve connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    S9-1 - SCV (E8-15)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    S9-1 or SCV (E8-15) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2009 Intake Manifold Runner Control Circuit Low (Bank 1) (+ P2010) (Aug 2013 – Jul 2014)P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (Jun 2011 – Jul 2012) →