2014 Hilux · Service Manual RESTRAINTS

B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit

Diagnostic trouble codes · Vehicles built from Aug 2013

Also covers:

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

DESCRIPTION

The front passenger side curtain shield squib circuit consists of the center airbag sensor and the front passenger side curtain shield airbag.
The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side curtain shield squib circuit.
DTC Code
Detection Condition
Trouble Area
B1835/58
When all conditions below are met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the front passenger side curtain shield squib circuit during primary check.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Curtain shield airbag assembly (front passenger side)
  3. Center airbag sensor assembly
B1836/58
When all conditions below are met:
  1. The center airbag sensor receives an open circuit signal in the front passenger side curtain shield squib circuit for 2 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Curtain shield airbag assembly (front passenger side)
  3. Center airbag sensor assembly
B1837/58
When all conditions below are met:
  1. The center airbag sensor receives a short circuit to ground signal in the front passenger side curtain shield squib circuit for 0.5 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Curtain shield airbag assembly (front passenger side)
  3. Center airbag sensor assembly
B1838/58
When all conditions below are met:
  1. The center airbag sensor receives a short circuit to B+ signal in the front passenger side curtain shield squib circuit for 0.5 seconds.
  2. Front passenger side curtain shield squib malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Curtain shield airbag assembly (front passenger side)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C194497E21
C194497E22

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).


1. CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



B
Go to step 6
A


2. CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)
C194791E01
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the curtain shield airbag RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835, B1836, B1837 or B1838 is not output.

    HINT:
    Codes other than DTC B1835, B1836, B1837, B1838 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH

3. CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the floor wire connector (on the curtain shield airbag RH side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB RH CIRCUIT)
C194792E03
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C21-2 (ICR-) - Body ground
    Ignition switch ON
    Below 1 V
    C21-1 (ICR+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C21-2 (ICR-) - C21-1 (ICR+)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C21-2 (ICR-) - C21-1 (ICR+)
    Always
    1 MΩ or higher
    C21-2 (ICR-) - Body ground
    C21-1 (ICR+) - Body ground



NG
REPLACE FLOOR WIRE
OK


5. CHECK CENTER AIRBAG SENSOR ASSEMBLY
C172068E04
  1. Connect the connectors to the curtain shield airbag RH and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835, B1836, B1837 or B1838 is not output

    HINT:
    Codes other than DTC B1835, B1836, B1837, B1838 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK

6. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)
C194791E02
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the curtain shield airbag RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835, B1836, B1837 or B1838 is not output.

    HINT:
    Codes other than DTC B1835, B1836, B1837, B1838 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

7. CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the floor wire connector (on the curtain shield airbag LH side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


8. CHECK FLOOR WIRE
C194792E02
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-2 (ICL-) - Body ground
    Ignition switch ON
    Below 1 V
    C22-1 (ICL+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C22-2 (ICL-) - C22-1 (ICL+)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C22-2 (ICL-) - C22-1 (ICL+)
    Always
    1 MΩ or higher
    C22-2 (ICL-) - Body ground
    C22-1 (ICL+) - Body ground



NG
REPLACE FLOOR WIRE
OK


9. CHECK CENTER AIRBAG SENSOR ASSEMBLY
C172068E08
  1. Connect the connectors to the curtain shield airbag LH and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1835, B1836, B1837 or B1838 is not output

    HINT:
    Codes other than DTC B1835, B1836, B1837, B1838 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK


← B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit (+ B1836/58, B1837/58, B1838/58) (Jun 2011 – Jul 2013)B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Jun 2011 – Jul 2013) →