2014 Hilux · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2012


1. INSTALL ACTUATOR ASSEMBLY WITH BRACKET (for Waste Gate Type Turbocharger)

  1. A148174E02
    Using SST, apply pressure to the actuator.
    SST
    09992-00242  

    NOTICE:
    Never apply more than 156 kPa (1.60 kgf/cm2, 23 psi) of pressure to the actuator.

    HINT:
    The actuator push rod stroke is determined by the plate washer shown in the illustration.

    Text in Illustration 
    *1
    Plate Washer

  1. Install the actuator with the 2 bolts and E-ring.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. A148175E02
    Set a dial indicator as shown in the illustration.
    Text in Illustration 
    *a
    Push Rod Stroke

  1. Using SST, apply a pressure of 114 kPa (1.16 kgf/cm2, 16.4 psi) to the actuator and measure the push rod stroke.

    SST
    09992-00242  

  1. Select the plate washer according to the table below.

    Plate Washer Selection Chart 
    Stroke Measurement
    Required Plate Washer Thickness
    1.20 to 1.70 mm (0.0472 to 0.0669 in.)
    -
    1.71 to 2.20 mm (0.0673 to 0.0866 in.)
    0.5mm (0.020 in.)
    2.21 to 2.70 mm (0.0870 to 0.1063 in.)
    1.0 mm (0.039 in.)
    2.71 to 3.20 mm (0.1067 to 0.1260 in.)
    1.5 mm (0.059 in.)
    3.21 to 3.70 mm (0.1264 to 0.4517 in.)
    2.0 mm (0.079 in.)
    3.71 to 4.20 mm (0.1461 to 0.1654 in.)
    2.5 mm (0.098 in.)
    4.21 to 4.70 mm (0.1657 to 0.1850 in.)
    3.0 mm (0.118 in.)
    4.71 to 5.20 mm (0.1854 to 0.2047 in.)
    3.5 mm (0.138 in.)
    5.21 to 5.70 mm (0.2051 to 0.2244 in.)
    4.0 mm (0.157 in.)
    5.71 to 6.20 mm (0.2248 to 0.2441 in.)
    4.5 mm (0.177 in.)
    6.21 to 6.70 mm (0.2445 to 0.2638 in.)
    5.0 mm (0.197 in.)
    6.71 to 7.20 mm (0.2642 to 0.2827 in.)
    5.5 mm (0.217 in.)
    7.21 to 7.70 mm (0.2839 to 0.3031 in.)
    6.0 mm (0.236 in.)
    7.71 to 8.20 mm (0.3035 to 0.3228 in.)
    6.5 mm (0.256 in.)

    NOTICE:
    1. Use a combination of plate washers of 0.5 mm (0.020 in.), 1.0 mm (0.039 in.) and 3.0 mm (0.118 in.) thickness.
    1. Use plate washers of the same thickness between the 2 locations of the actuator and compressor housing.
    1. If the plate washer thickness exceeds 3.5 mm (0.138 in.), replace the actuator installation bolts with the bolts from the kit.

  1. Using SST, apply 114 kPa (1.16 kgf/cm2, 16.4 psi) of pressure to the actuator, and install the selected plate washers between the actuator and compressor housing with the 2 bolts and E-ring.

    SST
    09992-00242  

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Using SST, apply a pressure of 114 kPa (1.16 kgf/cm2, 16.4 psi) to the actuator, and measure the actuator push rod stroke.

    SST
    09992-00242  

    Standard stroke:
    1.20 to 1.70 mm (0.0472 to 0.0669 in.)

    If the stroke is outside the specified range, select plate washers again.

  1. Connect the actuator hose.

  1. Remove SST.

  1. Apply yellow paint in lines across the actuator bolts and actuator bracket to indicate that the actuator has been correctly installed.

← INSPECTION (from Aug 2012)INSTALLATION (Jun 2011 – Jul 2012) →