2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

3. REMOVE INTERCOOLER ASSEMBLY
(Click here)

4. REMOVE NO. 1 ENGINE UNDER COVER

5. REMOVE NO. 2 ENGINE UNDER COVER

6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


7. REMOVE FRONT WHEEL RH

8. REMOVE FRONT FENDER APRON SEAL UPPER
  1. Remove the 5 clips and front fender apron seal upper.


9. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and front fender seal.


10. REMOVE AIR CLEANER ASSEMBLY

  1. A254009
    Detach the wire harness clamp and disconnect the mass air flow meter connector.

  1. Detach the ventilation hose clamp and remove the ventilation hose.

  1. Loosen the hose clamp and disconnect No. 1 air cleaner hose from the compressor inlet elbow.

  1. Remove the 2 bolts and air cleaner together with the No. 1 air cleaner hose.


11. REMOVE VENTILATION HOSE CLAMP

  1. A254010
    Remove the bolt and ventilation hose clamp.


12. REMOVE COMPRESSOR INLET ELBOW

  1. A254011
    Disconnect the 2 connectors and detach the wire harness clamp.

  1. Remove the 2 nuts, compressor inlet elbow and gasket.


13. REMOVE NO. 1 TURBO INSULATOR

  1. A255740
    Remove the 2 bolts and No. 1 turbo insulator.


14. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A255741
    Remove the bolt and No. 1 exhaust manifold heat insulator.


15. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A254012
    Remove the 2 bolts and No. 2 exhaust manifold heat insulator.


16. REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

  1. A254013
    Remove the 2 bolts and No. 3 exhaust manifold heat insulator.


17. REMOVE TURBINE OUTLET ELBOW STAY

  1. A254014
    Detach the wire harness clamp and remove the bolt, nut and turbine outlet elbow stay.


18. REMOVE NO. 2 TURBINE OUTLET ELBOW

  1. A254044
    Remove the 3 nuts, No. 2 turbine outlet elbow and gasket.


19. DISCONNECT NO. 1 FUEL PIPE

  1. A254045
    Detach the hose clamp and disconnect the No. 4 turbo water hose from the No. 4 water by-pass pipe.

  1. Disconnect the exhaust fuel addition injector connector.

  1. Remove the union bolt and gasket.

  1. Disconnect the No. 1 fuel pipe from the turbine outlet elbow.


20. REMOVE TURBINE OUTLET ELBOW
  1. Disconnect the No. 3 turbo water hose from the No. 3 water by-pass pipe.

  1. Remove the 3 nuts, turbine outlet elbow and gasket.

    A254046E01

    Text in Illustration 
    *1
    Gasket
    *2
    Union Bolt
    *3
    No. 3 Water By-pass Pipe
    *4
    No. 4 Water By-pass Pipe
    *5
    No. 3 Turbo Water Hose
    *6
    Turbine Outlet Elbow

  1. Remove the bolt, union bolt, gasket and No. 3 water by-pass pipe from the turbine outlet elbow.

  1. Remove the union bolt, gasket and No. 4 water by-pass pipe from the turbine outlet elbow.


21. DISCONNECT NO. 1 TURBO WATER HOSE

  1. A254047
    Disconnect the 2 No. 1 turbo water hoses.


22. REMOVE TURBOCHARGER STAY

  1. A254048
    Remove the 2 bolts, nut and turbocharger stay.


23. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

  1. A098817E03
    Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A in the illustration.


24. REMOVE TURBOCHARGER SUB-ASSEMBLY

  1. A211839
    Remove the 3 nuts, turbocharger and gasket.


25. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

  1. A254049
    Remove the 2 nuts, bolt, No. 1 turbo water pipe and gasket.

← SYSTEM DESCRIPTION (from Aug 2013)REMOVAL (Aug 2012 – Jul 2013) →