2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. REMOVE TAILPIPE ASSEMBLY
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the tailpipe from the center exhaust pipe and remove the gasket.

  1. Remove the tailpipe from the exhaust pipe support.


2. REMOVE CENTER EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the gasket.


3. REMOVE NO. 2 ENGINE UNDER COVER

4. SUPPORT TRANSMISSION AND TRANSFER ASSEMBLY

C111233
  1. Support the transmission with a transmission jack.


5. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Automatic Transmission)

G034256E02
  1. Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.


6. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Manual Transmission)

G034218E03
  1. Support the transmission rear side with a support stand.

  1. Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. Remove the 4 bolts, 4 nuts and frame crossmember.


7. REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET

  1. A254003
    Remove the 2 bolts and No. 2 exhaust pipe support bracket from the No. 3 frame crossmember.


8. REMOVE AIR FUEL RATIO SENSOR

A253513
  1. Disconnect the air fuel ratio sensor connector.

  1. A253514E01
    Using SST, remove the air fuel ratio sensor from the front exhaust pipe.
    SST
    09224-00010  


9. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A253992
    Disconnect the exhaust gas temperature sensor connector and detach the clamp.

  1. A253993
    Disconnect the No. 2 exhaust gas temperature sensor connector.

  1. A254213E01
    Disconnect the No. 3 exhaust gas temperature sensor connector and detach the clamp.
    Text in Illustration 
    *A
    for Manual Transmission
    *B
    for Automatic Transmission

  1. A253997
    Disconnect the No. 6 exhaust pipe air hose and No. 7 exhaust pipe air hose from the front exhaust pipe.

  1. A253999
    Remove the 2 exhaust pipe supports.

  1. A253998
    Remove the 3 nuts and front exhaust pipe.

  1. Remove the gasket.


10. REMOVE EXHAUST GAS TEMPERATURE SENSOR

A253518

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Using a 14 mm union nut wrench, remove the exhaust gas temperature sensor.


11. REMOVE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

A254000

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Detach the 5 clamps.

  1. Using a 14 mm union nut wrench, remove the No. 2 exhaust gas temperature sensor.


12. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A254002
    Remove the bolt and wiring harness clamp bracket.


13. REMOVE NO. 3 EXHAUST GAS TEMPERATURE SENSOR

A253520

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Using a 14 mm union nut wrench, remove the No. 3 exhaust gas temperature sensor.


14. REMOVE EXHAUST PIPE CLAMP SUB-ASSEMBLY

  1. A254001
    Remove the bolt, nut and exhaust pipe clamp.


15. REMOVE MONOLITHIC CONVERTER PROTECTOR

  1. A254672
    Remove the 4 bolts and 4 nuts.

  1. A254673E01
    Remove the upper monolithic converter protector and lower monolithic converter protector.
    Text in Illustration 
    *1
    Upper Monolithic Converter Protector
    *2
    Lower Monolithic Converter Protector


16. REMOVE CONVERTER PROTECTOR STAY

  1. A254674E01
    Remove the 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.
    Text in Illustration 
    *1
    No. 1 Converter Protector Stay
    *2
    No. 2 Converter Protector Stay

← COMPONENTS (from Jun 2011)INSTALLATION (from Jun 2011) →