2014 Hilux · Service Manual ENGINE

P245C EGR Cooler Bypass Control Circuit Low

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The No. 2 EGR valve (EGR cooler bypass valve) is installed on the opening of the EGR cooler. The ECM optimizes exhaust gas temperature and improves exhaust gas purification by performing the following: 1) using information from the crankshaft position sensor, engine coolant temperature sensor, load signals, etc.; 2) sending the negative pressure (applied to the diaphragm) through the VSV (for No. 2 EGR valve); and 3) opens and closes the switching valve.
This DTC is designed to detect open or shorts in the VSV (for No. 2 EGR valve) circuit.
DTC No.
DTC Detection Condition
Trouble Area
P245C
Open in VSV for No. 2 EGR valve circuit for 0.5 seconds
(1 trip detection logic)
  1. VSV for No. 2 EGR valve
  2. Open in VSV for No. 2 EGR valve circuit
  3. ECM
P245D
Short in VSV for No. 2 EGR valve circuit for 0.5 seconds
(1 trip detection logic)
  1. VSV for No. 2 EGR valve
  2. Short in VSV for No. 2 EGR valve circuit
  3. ECM

WIRING DIAGRAM

A155670E04

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT NO. 2 VACUUM SWITCHING VALVE FOR NO. 2 EGR VALVE (RESISTANCE)

  1. A155051E02
    Disconnect the V7 VSV for No. 2 EGR valve connector.

  1. Measure the resistance of the VSV for No. 2 EGR valve.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    37 to 44 Ω



NG
REPLACE NO. 2 VACUUM SWITCHING VALVE FOR NO. 2 EGR VALVE
OK


2. INSPECT NO. 2 VACUUM SWITCHING VALVE FOR NO. 2 EGR VALVE (POWER SOURCE VOLTAGE)

  1. A154589E05
    Disconnect the V7 VSV for No. 2 EGR valve connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector and body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    V7-1 - Body ground
    11 to 14 V



NG
Go to step 4
OK


3. CHECK HARNESS AND CONNECTOR (VSV FOR NO. 2 EGR VALVE - ECM)

  1. A155052E02
    Disconnect the V7 VSV for No. 2 EGR valve connector.

  1. Remove the E7 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    V7-2 - ECBV (E7-19)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    V7-2 or ECBV (E7-19) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - VSV FOR NO. 2 EGR VALVE)

  1. G034915E04
    Remove the integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J integration relay connector.

  1. Disconnect the V7 VSV for No. 2 EGR valve connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    1J-5 - V7-1
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    1J-5 or V7-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT


← P2226 Barometric Pressure Circuit (+ P2228, P2229) (from Aug 2014)P245C EGR Cooler Bypass Control Circuit Low (+ P245D) (Aug 2012 – Jul 2013) →