2014 Hilux · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR

  1. NO. 1 JUNCTION CONNECTOR
    C190573E06

    No. 1 Junction Connector
    Wiring Color
    Connect to
    J54-4 (CANH)
    B
    No. 2 junction connector
    J54-1 (CANL)
    W
    J54-12 (CANH)
    B
    ECM
    J54-6 (CANL)
    W
    J54-13 (CANH)
    R
    Skid control ECU
    J54-7 (CANL)
    W

  2. NO. 2 JUNCTION CONNECTOR
    C240979E02

    No. 2 Junction Connector
    Wiring Color
    Connect to
    J59-5 (CANH)
    B
    No. 1 junction connector
    J59-16 (CANL)
    W
    J59-6 (CANH)
    B
    No. 3 junction connector
    J59-17 (CANL)
    W
    J59-7 (CANH)
    R
    Yaw rate sensor
    J59-18 (CANL)
    W

  3. NO. 3 JUNCTION CONNECTOR
    C190575E03

    Wiring Color 
    Junction Connector A Side
    Color (CANH Side)
    Color (CANL Side)
    No. 2 junction connector and ECM (J50)
    B
    W
    Steering angle sensor (J51)
    W
    R
    Wiring Color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    DLC3 (J49)
    W
    R


TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR
C135249
Terminal No.
Symbol
1
CANL
2
CANH

CHECK DLC3
H102621E26
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    W - R
    Ignition switch off
    54 to 69 Ω
    D1-6 (CANH) - D1-4 (CG)
    W - G
    Ignition switch off
    200 Ω or higher
    D1-14 (CANL) - D1-4 (CG)
    R - G
    Ignition switch off
    200 Ω or higher
    D1-6 (CANH) - D1-16 (BAT)
    W - G
    Ignition switch off
    6 kΩ or higher
    D1-14 (CANL) - D1-16 (BAT)
    R - G
    Ignition switch off
    6 kΩ or higher


CHECK SKID CONTROL ECU
C190577E05
  1. Disconnect the S35 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    S35-25 (CANH) - S35-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    S35-25 (CANH) - S35-1 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    S35-14 (CANL) - S35-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S35-25 (CANH) - S35-12 (+BS)
    B - W-R
    Ignition switch off
    6 kΩ or higher
    S35-14 (CANL) - S35-12 (+BS)
    W - W-R
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV, 2KD-FTV [w/ DPF])
E191646E10
  1. Disconnect the E25, E30 and E31 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    E30-35 (CANH) - E30-36 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E30-35 (CANH) - E25-1 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E30-36 (CANL) - E25-1 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E30-35 (CANH) - E31-23 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E30-36 (CANL) - E31-23 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV, 2KD-FTV [w/o DPF])
C190578E03
  1. Disconnect the E6 and E7 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    E6-24 (CANH) - E6-23 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E6-24 (CANH) - E7-7 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E6-23 (CANL) - E7-7 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E6-24 (CANH) - E6-2 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E6-23 (CANL) - E6-2 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1GR-FE)
G036662E35
  1. Disconnect the E13, E14 and E17 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    E13-33 (CANH) - E13-34 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E13-33 (CANH) - E17-1 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E13-34 (CANL) - E17-1 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E13-33 (CANH) - E14-3 (BATT)
    B - L
    Ignition switch off
    6 kΩ or higher
    E13-34 (CANL) - E14-3 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK STEERING ANGLE SENSOR
C190672E04
  1. Disconnect the S37 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    S37-4 (CANH) - S37-3 (CANL)
    W - R
    Ignition switch off
    54 to 69 Ω
    S37-4 (CANH) - S37-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S37-3 (CANL) - S37-2 (ESS)
    R - W-B
    Ignition switch off
    200 Ω or higher
    S37-4 (CANH) - S37-6 (BAT)
    W - B
    Ignition switch off
    6 kΩ or higher
    S37-3 (CANL) - S37-6 (BAT)
    R - B
    Ignition switch off
    6 kΩ or higher


CHECK YAW RATE SENSOR
C190673E06
  1. Disconnect the Y1 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    Y1-3 (CANH) - Y1-1 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    Y1-2 (CANL) - Y1-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    Y1-3 (CANH) - D1-16 (BAT)
    B - G
    Ignition switch off
    6 kΩ or higher
    Y1-2 (CANL) - D1-16 (BAT)
    W - G
    Ignition switch off
    6 kΩ or higher

← TERMINALS OF ECU (Aug 2012 – Jul 2013)TERMINALS OF ECU (from Aug 2014) →