TERMINALS OF ECU
System information · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
| JUNCTION CONNECTOR |
NO. 1 JUNCTION CONNECTOR


No. 1 Junction Connector
Wiring Color
Connect to
J54-4 (CANH)
B
No. 2 junction connector
J54-1 (CANL)
W
J54-12 (CANH)
B
ECM
J54-6 (CANL)
W
J54-13 (CANH)
R
Skid control ECU
J54-7 (CANL)
W
NO. 2 JUNCTION CONNECTOR


No. 2 Junction Connector
Wiring Color
Connect to
J59-5 (CANH)
B
No. 1 junction connector
J59-16 (CANL)
W
J59-6 (CANH)
B
No. 3 junction connector
J59-17 (CANL)
W
J59-7 (CANH)
R
Yaw rate sensor
J59-18 (CANL)
W
NO. 3 JUNCTION CONNECTOR


Wiring Color Junction Connector A Side
Color (CANH Side)
Color (CANL Side)
No. 2 junction connector and ECM (J50)
B
W
Steering angle sensor (J51)
W
R
Wiring Color Junction Connector B Side
Color (CANH Side)
Color (CANL Side)
DLC3 (J49)
W
R
| TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR |
![]() ![]() |
| Terminal No. |
Symbol |
| 1 |
CANL |
| 2 |
CANH |
| CHECK DLC3 |
![]() ![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
D1-6 (CANH) - D1-14 (CANL)
W - R
Ignition switch off
54 to 69 Ω
D1-6 (CANH) - D1-4 (CG)
W - G
Ignition switch off
200 Ω or higher
D1-14 (CANL) - D1-4 (CG)
R - G
Ignition switch off
200 Ω or higher
D1-6 (CANH) - D1-16 (BAT)
W - G
Ignition switch off
6 kΩ or higher
D1-14 (CANL) - D1-16 (BAT)
R - G
Ignition switch off
6 kΩ or higher
| CHECK SKID CONTROL ECU |


Disconnect the S35 ECU connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
S35-25 (CANH) - S35-14 (CANL)
B - W
Ignition switch off
54 to 69 Ω
S35-25 (CANH) - S35-1 (GND1)
B - W-B
Ignition switch off
200 Ω or higher
S35-14 (CANL) - S35-1 (GND1)
W - W-B
Ignition switch off
200 Ω or higher
S35-25 (CANH) - S35-12 (+BS)
B - W-R
Ignition switch off
6 kΩ or higher
S35-14 (CANL) - S35-12 (+BS)
W - W-R
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1KD-FTV, 2KD-FTV [w/ DPF]) |


Disconnect the E25, E30 and E31 ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
E30-35 (CANH) - E30-36 (CANL)
B - W
Ignition switch off
108 to 132 Ω
E30-35 (CANH) - E25-1 (E1)
B - BR
Ignition switch off
200 Ω or higher
E30-36 (CANL) - E25-1 (E1)
W - BR
Ignition switch off
200 Ω or higher
E30-35 (CANH) - E31-23 (BATT)
B - L
Ignition switch off
6 kΩ or higher
E30-36 (CANL) - E31-23 (BATT)
W - L
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1KD-FTV, 2KD-FTV [w/o DPF]) |


Disconnect the E6 and E7 ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
E6-24 (CANH) - E6-23 (CANL)
B - W
Ignition switch off
108 to 132 Ω
E6-24 (CANH) - E7-7 (E1)
B - BR
Ignition switch off
200 Ω or higher
E6-23 (CANL) - E7-7 (E1)
W - BR
Ignition switch off
200 Ω or higher
E6-24 (CANH) - E6-2 (BATT)
B - L
Ignition switch off
6 kΩ or higher
E6-23 (CANL) - E6-2 (BATT)
W - L
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1GR-FE) |


Disconnect the E13, E14 and E17 ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
E13-33 (CANH) - E13-34 (CANL)
B - W
Ignition switch off
108 to 132 Ω
E13-33 (CANH) - E17-1 (E1)
B - BR
Ignition switch off
200 Ω or higher
E13-34 (CANL) - E17-1 (E1)
W - BR
Ignition switch off
200 Ω or higher
E13-33 (CANH) - E14-3 (BATT)
B - L
Ignition switch off
6 kΩ or higher
E13-34 (CANL) - E14-3 (BATT)
W - L
Ignition switch off
6 kΩ or higher
| CHECK STEERING ANGLE SENSOR |


Disconnect the S37 sensor connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
S37-4 (CANH) - S37-3 (CANL)
W - R
Ignition switch off
54 to 69 Ω
S37-4 (CANH) - S37-2 (ESS)
W - W-B
Ignition switch off
200 Ω or higher
S37-3 (CANL) - S37-2 (ESS)
R - W-B
Ignition switch off
200 Ω or higher
S37-4 (CANH) - S37-6 (BAT)
W - B
Ignition switch off
6 kΩ or higher
S37-3 (CANL) - S37-6 (BAT)
R - B
Ignition switch off
6 kΩ or higher
| CHECK YAW RATE SENSOR |


Disconnect the Y1 sensor connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbols)
Wiring Color
Switch Condition
Specified Condition
Y1-3 (CANH) - Y1-2 (CANL)
B - W
Ignition switch off
54 to 69 Ω
Y1-3 (CANH) - Y1-1 (GND)
B - W-B
Ignition switch off
200 Ω or higher
Y1-2 (CANL) - Y1-1 (GND)
W - W-B
Ignition switch off
200 Ω or higher
Y1-3 (CANH) - D1-16 (BAT)
B - G
Ignition switch off
6 kΩ or higher
Y1-2 (CANL) - D1-16 (BAT)
W - G
Ignition switch off
6 kΩ or higher

