2014 Hilux · Service Manual COMMUNICATION SYSTEM

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
When either condition below is met:
  1. ECM (Engine) is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or ECM
  2. Harness or connector
  3. ECM

WIRING DIAGRAM

C245037E01
C245038E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

  1. for 1KD-FTV, 2KD-FTV (w/ DPF):C245040E01

    1. Disconnect the E25, E30 and E31 ECM connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E31-24 (+B) - Body ground
      When battery's positive (+) voltage is applied to terminal E30-11 (MREL)
      11 to 14 V
      E31-23 (BATT) - Body ground
      Always
      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E25-1 (E1) - Body ground
      Always
      Below 1 Ω
      E25-13 (E02) - Body ground
      Always
      Below 1 Ω
      E25-12 (E01) - Body ground
      Always
      Below 1 Ω

  1. for 1KD-FTV, 2KD-FTV (w/o DPF):C190784E03

    1. Disconnect the E5, E6, E7 and E8 ECM connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E5-1 (+B) - Body ground
      When battery's positive (+) voltage is applied to terminal E5-8 (MREL)
      11 to 14 V
      E6-2 (BATT) - Body ground
      Always
      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E7-7 (E1) - Body ground
      Always
      Below 1 Ω
      E8-6 (E02) - Body ground
      Always
      Below 1 Ω
      E8-7 (E01) - Body ground
      Always
      Below 1 Ω

  1. for 1GR-FE:C245041E01

    1. Disconnect the E14, E15 and E17 ECM connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E14-1 (+B) - Body ground
      When battery's positive (+) voltage is applied to terminal E14-8 (MREL)
      11 to 14 V
      E14-2 (+B2) - Body ground
      When battery's positive (+) voltage is applied to terminal E14-8 (MREL)
      11 to 14 V
      E14-3 (BATT) - Body ground
      Always
      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E17-1 (E1) - Body ground
      Always
      Below 1 Ω
      E15-7 (E01) - Body ground
      Always
      Below 1 Ω
      E15-6 (E02) - Body ground
      Always
      Below 1 Ω

Result 
Result
Proceed to
OK (for 1KD-FTV)
A
OK (for 2KD-FTV)
B
OK (for 1GR-FE)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← ECM Communication Stop Mode (Jun 2011 – Jul 2012)ECM Communication Stop Mode (from Aug 2013) →