Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › PRESSURE SWITCH
REMOVAL
Removal / installation · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
1.
RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
Start up the engine.
A/C switch is ON.
Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.
Stop the engine.
Using SST, Recover the refrigerant from the A/C system using a refrigerant recovery unit.
SST
09985-20010
(09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
2.
REMOVE RADIATOR GRILLE
Put protective tape around the radiator grille.
Text in Illustration
*1
Protective Tape
Remove the 2 clips and 2 screws.
Detach the 6 claws and remove the radiator grille.
3.
REMOVE FRONT BUMPER COVER
Remove the 3 clips and 6 screws.
Put protective tape around the front bumper cover.
Text in Illustration
*1
Protective Tape
Remove the 2 bolts, 2 screws and 5 clips.
w/ Fog Light: Disconnect the 2 fog light connectors.
w/ Headlight Cleaner System: Disconnect the No. 1 headlight cleaner hose.
Detach the 6 claws and remove the front bumper cover.
4.
REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH (for 4WD and Pre-Runner)
Remove the 2 clips, 3 bolts and engine side cover.
5.
REMOVE ENGINE SIDE COVER SUB-ASSEMBLY RH (for 4WD and Pre-Runner)
HINT:
Use the same procedure described for the LH side.
6.
REMOVE ENGINE UNDER COVER (except 4WD and Pre-Runner)
Remove the 4 clips, 5 bolts and engine under cover.
7.
REMOVE FRONT BUMPER REINFORCEMENT EXTENSION LH (for 4WD and Pre-Runner)
Detach the 2 claws and remove the front bumper reinforcement extension.
8.
REMOVE FRONT BUMPER REINFORCEMENT EXTENSION RH (for 4WD and Pre-Runner)
HINT:
Use the same procedure described for the LH side.
9.
REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Remove the 4 nuts and front bumper reinforcement.
10.
REMOVE RADIATOR SIDE DEFLECTOR RH
Remove the 3 clips and radiator side deflector RH.
11.
REMOVE V-BANK COVER (for 1GR-FE)
Remove the 2 nuts and the V-bank cover.
12.
REMOVE AIR CLEANER ASSEMBLY (for 1GR-FE)
Disconnect the vacuum hose.
Disconnect the MAF meter connector.
Remove the 2 wire harness clamps.
Loosen the 2 hose clamps.
Remove the 2 bolts and air cleaner.
13.
REMOVE AIR CLEANER ASSEMBLY (for 1KD-FTV, 2KD-FTV)
for Ventilation Hose Type: Disconnect the ventilation hose.
w/ Mass Air Flow Meter: Disconnect the mass air flow meter sensor connector.
w/ Intake Air Temperature Sensor: Disconnect the intake air temperature sensor connector.
Loosen the hose clamp.
Remove the 2 bolts and air cleaner.
14.
REMOVE INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY (for 2TR-FE)
Disconnect the vacuum hose.
Disconnect the No. 2 ventilation hose.
Disconnect the MAF meter connector and wire harness clamps.
Loosen the hose clamp and remove the 4 bolts, air cleaner and intake air connector assembly.
15.
REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Disconnect the connector.
Remove the 3 bolts and air conditioning tube and accessory assembly (pressure switch).
Remove the O-rings from the air conditioning tube and accessory assembly (pressure switch).
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.