2014 Hilux · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. A/C switch is ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Using SST, Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    SST
    09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)


2. REMOVE RADIATOR GRILLE

  1. B277710E01
    Put protective tape around the radiator grille.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 2 clips and 2 screws.

  1. B277711
    Detach the 6 claws and remove the radiator grille.


3. REMOVE FRONT BUMPER COVER

  1. B277694
    Remove the 3 clips and 6 screws.

  1. B283433E01
    Put protective tape around the front bumper cover.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 2 bolts, 2 screws and 5 clips.

  1. w/ Fog Light:
    Disconnect the 2 fog light connectors.

  1. w/ Headlight Cleaner System:
    Disconnect the No. 1 headlight cleaner hose.

  1. B277696
    Detach the 6 claws and remove the front bumper cover.


4. REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH (for 4WD and Pre-Runner)

  1. B277698
    Remove the 2 clips, 3 bolts and engine side cover.


5. REMOVE ENGINE SIDE COVER SUB-ASSEMBLY RH (for 4WD and Pre-Runner)

HINT:
Use the same procedure described for the LH side.


6. REMOVE ENGINE UNDER COVER (except 4WD and Pre-Runner)

  1. B277697
    Remove the 4 clips, 5 bolts and engine under cover.


7. REMOVE FRONT BUMPER REINFORCEMENT EXTENSION LH (for 4WD and Pre-Runner)

  1. B277699
    Detach the 2 claws and remove the front bumper reinforcement extension.


8. REMOVE FRONT BUMPER REINFORCEMENT EXTENSION RH (for 4WD and Pre-Runner)

HINT:
Use the same procedure described for the LH side.


9. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

B277700
  1. Remove the 4 nuts and front bumper reinforcement.


10. REMOVE RADIATOR SIDE DEFLECTOR RH

E225445
  1. Remove the 3 clips and radiator side deflector RH.


11. REMOVE V-BANK COVER (for 1GR-FE)

  1. A112983
    Remove the 2 nuts and the V-bank cover.


12. REMOVE AIR CLEANER ASSEMBLY (for 1GR-FE)

  1. A075595
    Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Remove the 2 wire harness clamps.

  1. A075596
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts and air cleaner.


13. REMOVE AIR CLEANER ASSEMBLY (for 1KD-FTV, 2KD-FTV)
  1. w/o EGR Cooler:
    Disconnect the ventilation hose.

  1. w/ Mass Air Flow Meter:
    Disconnect the mass air flow meter sensor connector.

  1. w/ Intake Air Temperature Sensor:
    Disconnect the intake air temperature sensor connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.


14. REMOVE INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY (for 2TR-FE)

A099871E01
  1. Disconnect the vacuum hose.

  1. Disconnect the No. 2 ventilation hose.

  1. Disconnect the MAF meter connector and wire harness clamps.

  1. Loosen the hose clamp and remove the 4 bolts, air cleaner and intake air connector assembly.


15. REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Disconnect the connector.

  1. Remove the 3 bolts and air conditioning tube and accessory assembly (pressure switch).

    E229029

  1. Remove the O-rings from the air conditioning tube and accessory assembly (pressure switch).

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

← REMOVAL (Jun 2011 – Jul 2012)REMOVAL (from Aug 2013) →