2014 Hilux · Service Manual CRUISE CONTROL SYSTEM

Clutch Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

When the clutch pedal is released, the ECM receives positive (+) battery voltage through the ECU-IG&GAUGE fuse. While depressing the clutch pedal, the clutch switch sends a signal to terminal 21(D)*1, 15(CLSW)*2 or 10(CLSW)*3 of the ECM. The ECM cancels cruise control when terminal 21(D)*1, 15(CLSW)*2 or 10(CLSW)*3 receives the signal.
  1. *1: for 1GR-FE
  2. *2: for 1KD-FTV (for DPF)
  3. *3: for 1KD-FTV (except DPF)

WIRING DIAGRAM

E149076E08
E149076E09

INSPECTION PROCEDURE


1. INSPECT FUSE (ECU-IG&GAUGE)
  1. Remove the ECU-IG&GAUGE fuse from the driver side junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG&GAUGE fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

  1. E216586E01
    Disconnect the E13*1, E27*2 or E6*3 ECM connector.*1: for 1GR-FE*2: for 1KD-FTV (for DPF)*3: for 1KD-FTV (except DPF)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1GR-FE:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-21 (D) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    for 1KD-FTV (for DPF):
    Tester Connection
    Switch Condition
    Specified Condition
    E27-15 (CLSW) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    for 1KD-FTV (except DPF):
    Tester Connection
    Switch Condition
    Specified Condition
    E6-10 (CLSW) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

3. INSPECT CLUTCH SWITCH ASSEMBLY

  1. E171630E01
    Remove the clutch switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin pushed
    Below 1 Ω
    Pin not pushed
    10 kΩ or higher



NG
REPLACE CLUTCH SWITCH ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH)

  1. E216587E01
    Disconnect the E13*1, E27*2 or E6*3 ECM connector.*1: for 1GR-FE*2: for 1KD-FTV (for DPF)*3: for 1KD-FTV (except DPF)

  1. Disconnect the C23 clutch switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    E13-21 (D) - C23-2
    Always
    Below 1 Ω
    E13-21 (D) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for DPF):
    Tester Connection
    Condition
    Specified Condition
    E27-15 (CLSW) - C23-2
    Always
    Below 1 Ω
    E27-15 (CLSW) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (except DPF):
    Tester Connection
    Condition
    Specified Condition
    E6-10 (CLSW) - C23-2
    Always
    Below 1 Ω
    E6-10 (CLSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH SWITCH)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - CLUTCH SWITCH)


← P0575 Cruise Control Input Circuit (+ P0607) (from Jun 2011)Cruise Control Switch Circuit (from Jun 2011) →