2014 Hilux · Service Manual CRUISE CONTROL SYSTEM

Cruise Control Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

This circuit sends signals to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Then terminal CCS of the ECM receives the voltage according to the switch condition.

WIRING DIAGRAM

E216588E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)

  1. E149007E02
    Using the intelligent tester, read the Data List.
    Cruise Control 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    CCS Main SW M-CPU
    Cruise control main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    (-SET) switch signal / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    (+RES) switch signal / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -

    OK:
    The intelligent tester display changes according to operation of cruise control main switch.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY
E149006E03
  1. Remove the cruise control main switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 3
    Neutral
    10 kΩ or higher
    Pushed to +RES
    235 to 245 Ω
    Pushed to -SET
    617 to 643 Ω
    Pushed to CANCEL
    1509 to 1571 Ω
    Main switch pushed off
    10 kΩ or higher
    Main switch pushed on
    Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH ASSEMBLY
OK


3. INSPECT CRUISE CONTROL SWITCH WIRE
E149008E06
  1. Remove the cruise control switch wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - B-3
    Always
    Below 1 Ω
    A-4 - B-1



NG
REPLACE CRUISE CONTROL SWITCH WIRE
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY
E158922E04
  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - 1 (CCS)
    Always
    Below 1 Ω
    A-4 - 2 (ECC)
    Always
    Below 1 Ω



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
E216589E01
  1. Disconnect the S42 spiral cable connector.

  1. Disconnect the E13*1, E31*2 or E5*3 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV (for DPF)
    3. *3: for 1KD-FTV (except DPF)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    S42-1 (CCS) - E13-2 (CCS)
    Always
    Below 1 Ω
    S42-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S42-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for DPF):
    Tester Connection
    Condition
    Specified Condition
    S42-1 (CCS) - E31-14 (CCS)
    Always
    Below 1 Ω
    S42-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S42-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (except DPF):
    Tester Connection
    Condition
    Specified Condition
    S42-1 (CCS) - E5-21 (CCS)
    Always
    Below 1 Ω
    S42-2 (ECC) - Body ground
    Always
    Below 1 Ω
    S42-1 (CCS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Clutch Switch Circuit (from Jun 2011)Cruise Main Indicator Light Circuit (from Jun 2011) →