2014 Hilux · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for RHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the RH side.


1. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (w/o Front Seat Side Airbag)
  1. Install the separate type front seatback spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL NO. 1 SEAT WIRE

  1. B286469
    Attach the 2 wire harness clamps to install the No. 1 seat wire.

  1. w/ Front Seat Side Airbag:
    Connect the front power seat motor assembly (for Reclining) connector.


3. INSTALL FRONT SEAT WIRE RH

B291580
  1. Attach the 2 claws to install the front seat wire RH.

  1. Attach the wire harness clamp.


4. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
  1. Attach the 4 claws to install the front lower seat cushion shield LH.

  1. Install the screw.


5. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH
  1. Attach the 4 claws to install the front lower seat cushion shield RH.

  1. Install the screw.


6. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)
(Click here)

7. INSTALL POWER SEAT MOTOR ASSEMBLY (for Slide)
(Click here)

8. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining, w/o Front Seat Side Airbag)
(Click here)

9. INSTALL RECLINING ADJUSTER INSIDE COVER LH (w/o Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover LH.

  1. Install the screw.


10. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the claw to install the reclining adjuster inside cover LH.

  1. Install the screw.


11. INSTALL RECLINING ADJUSTER INSIDE COVER RH (w/o Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover RH.

  1. Install the screw.


12. INSTALL RECLINING ADJUSTER INSIDE COVER RH
  1. Attach the claw to install the reclining adjuster inside cover RH.

  1. Install the screw.


13. INSTALL NO. 1 SEATBACK CLOTH

  1. B277283
    Install the No. 1 seatback cloth.


14. INSTALL SEPARATE TYPE FRONT SEATBACK PAD

  1. B207459
    Install the separate type front seatback pad to the separate type front seatback spring assembly.


15. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (for LHD, w/ Seat Heater System)
  1. Set the front seatback heater assembly LH on the separate type front seatback cover.

  1. Using a tacker, install the front seatback heater assembly LH to the separate type front seatback cover with 6 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.


    B284713E01
    Text in Illustration 
    *1
    Tack Pin
    *2
    Separate Type Front Seatback Cover
    *3
    Listing Pocket of Separate Type Front Seatback Cover
    -
    -


16. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

  1. Using hog ring pliers, attach the strap of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


    B284735E01
    Text in Illustration 
    *A
    w/o Front Seat Side Airbag
    *B
    w/ Front Seat Side Airbag
    *1
    Hog Ring Pliers
    -
    -
    *a
    Front view of front seatback
    *b
    Rear view of front seatback

  1. Attach the 4 claws to install the 2 front seat headrest supports.

  1. B284733
    w/ Front Seat Side Airbag:
    Attach the separate type front seatback cover bracket and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the separate type front seatback cover is installed, make sure the separate type front seatback cover bracket is not twisted.

  1. B284731
    Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.

  1. B284729E01
    Using hog ring pliers, attach the strap of the separate type front seatback cover together with the No. 1 seatback cloth to the separate type front seatback spring assembly with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers

  1. B286377
    for LHD, w/ Seat Heater System:
    Pass the front seatback heater assembly LH wire harness through the hole of the separate type front seatback cover.

  1. B284727E01
    Pass the No. 1 seat wire through the hole of the separate type front seatback cover.

  1. Using hog ring pliers, attach the wires at the bottom of the separate type front seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers

  1. B284721
    w/o Front Seat Side Airbag:
    Connect the No. 1 seat wire connector and attach the wire harness clamp.


17. INSTALL RECLINING ADJUSTER INSIDE COVER LH (w/ Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover LH.


18. INSTALL RECLINING ADJUSTER INSIDE COVER RH (w/ Front Seat Side Airbag)
  1. Attach the guide to install the reclining adjuster inside cover RH.


19. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/ Front Seat Side Airbag)
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the 2 screws.

  1. B284722
    for LHD, w/ Seat Heater System:
    Attach the front seatback heater assembly LH wire harness clamp.

  1. B284721
    Connect the No. 1 seat wire connector and attach the wire harness clamp.

  1. B284720
    Attach the 4 front seat airbag wire harness clamps.


20. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (for LHD, w/ Seat Heater System)

B284714E01
  1. Set the front seat cushion heater on the separate type front seat cushion cover.

  1. Using a tacker, install the front seat cushion heater to the separate type front seat cushion cover with 12 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.

    Text in Illustration 
    *1
    Tack Pin
    *2
    Separate Type Front Seat Cushion Cover
    *3
    Front Seat Cushion Heater Assembly LH


21. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B207627E02
    Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


22. INSTALL FRONT SEAT CUSHION COVER WITH PAD
  1. Attach the hooks to install the front seat cushion cover with pad.

  1. Bend the 2 front seat cushion frame claws downward.

  1. B284719
    for LHD, w/ Seat Heater System:

    1. Attach the 4 front seat cushion heater assembly LH clamps.

    2. Connect the 2 front seat cushion heater assembly LH connectors.

  1. B207083E02
    Using hog ring pliers, attach the rubber bands of the separate type front seatback cover to the seat cushion spring with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


23. INSTALL FRONT SEAT CUSHION COVER RH
  1. Install the front seat cushion cover RH.


24. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

B284022E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect the connector and attach the 3 clamps.


25. INSTALL FRONT SEAT INNER CUSHION SHIELD RH

  1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat inner cushion shield RH.

    B278523

  1. B278521
    Attach the claw to temporarily install the front seat inner cushion shield RH.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. B278522
    Attach the guide and claw.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. Install the screw.


26. INSTALL FRONT POWER SEAT SWITCH RH
  1. Connect the connector.

  1. Install the front power seat switch RH with the 3 screws.


27. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD RH
  1. Attach the 2 claws to install the front inner No. 1 seat cushion shield RH.

  1. Install the 2 screws.


28. INSTALL FRONT SEAT CUSHION SHIELD RH
  1. Attach the claw and guide to install the front seat cushion shield RH.

  1. Install the 3 screws.

  1. Install the 2 screws.


29. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

  1. B207446
    Attach the 4 claws to install the slide and vertical power seat switch knob.


30. INSTALL RECLINING POWER SEAT SWITCH KNOB

  1. B207447
    Attach the 2 claws to install the reclining power seat switch knob.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (Aug 2012 – Jul 2013) →