2014 Hilux · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)

  1. B207168E02
    Using a 4 mm socket hexagon wrench, install the power seat motor assembly (for Rear Lifter) with the 2 bolts.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

  1. Clean the threads of the "TORX" bolt for the adjust screw with non-residue solvent (when reusing the "TORX" bolt).

  1. Apply adhesive to the threads of the "TORX" bolt for the adjust screw (when reusing the "TORX" bolt).

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    Text in Illustration 
    *1
    Adjust Screw

  1. Using a T40 "TORX" socket wrench, install the "TORX" bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the connector.

  1. Using a T40 "TORX" socket wrench, install the tilt rod with the 2 "TORX" bolts for the tilt rod.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Install the nut.

  1. Install the seat cushion frame with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. B207524
    Attach the 4 clamps indicated by the arrows in the illustration to install the seat cushion spring.

  1. Attach the 2 wire harness clamps.


2. INSTALL FRONT SEAT CUSHION COVER WITH PAD
  1. Attach the hooks to install the front seat cushion cover with pad.

  1. Bend the 2 front seat cushion frame claws downward.

  1. B284719
    for LHD, w/ Seat Heater System:

    1. Attach the 4 front seat cushion heater assembly LH clamps.

    2. Connect the 2 front seat cushion heater assembly LH connectors.

  1. B207083E02
    Using hog ring pliers, attach the rubber bands of the separate type front seatback cover to the seat cushion spring with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


3. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

B284022E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect the connector and attach the 3 clamps.


4. INSTALL FRONT SEAT INNER CUSHION SHIELD RH

  1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat inner cushion shield RH.

    B278523

  1. B278521
    Attach the claw to temporarily install the front seat inner cushion shield RH.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. B278522
    Attach the guide and claw.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. Install the screw.


5. INSTALL FRONT POWER SEAT SWITCH RH
  1. Connect the connector.

  1. Install the front power seat switch RH with the 3 screws.


6. INSTALL FRONT SEAT CUSHION SHIELD RH
  1. Attach the claw and guide to install the front seat cushion shield RH.

  1. Install the 3 screws.

  1. Install the 2 screws.


7. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

  1. B207446
    Attach the 4 claws to install the slide and vertical power seat switch knob.


8. INSTALL RECLINING POWER SEAT SWITCH KNOB

  1. B207447
    Attach the 2 claws to install the reclining power seat switch knob.


9. INSTALL FRONT SEAT ASSEMBLY
(Click here)

10. INSPECT FRONT SEAT ASSEMBLY
(Click here)
← INSTALLATION (Aug 2012 – Jul 2013)COMPONENTS (from Jun 2011) →