ABS Warning Light Remains ON
Circuit diagnosis · Vehicles built Apr 2012 – Jul 2012
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When one of the following conditions is met, the ABS warning light remains on:- The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU.
- There is a malfunction in the skid control ECU internal circuit.
- There is an open in the harness between the combination meter and the skid control ECU.
- The anti-lock brake system is defective.
- w/ Rear Differential Lock:
The rear differential is locked.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK FOR DTC |
Turn the ignition switch off.
Check if DTCs for the ABS are output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
- OK:
- The connector is securely connected.
|
|
||||
| OK | |
| 3. CHECK TERMINAL VOLTAGE (IG1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S35-34 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-1 (GND1) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C25 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-10 (WA) - C25-38
Always
Below 1 Ω
S35-10 (WA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK TERMINAL VOLTAGE (EXI3 TERMINAL) |
Turn the ignition switch off.

Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S35-28 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
Result Result
Proceed to
NG
w/ Rear Differential Lock
A
w/o Rear Differential Lock
B
OK
C
|
|
||||
|
|
||||
| A | |
| 7. CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL CIRCUIT) |
Turn the ignition switch off.
Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.
Disconnect the rear differential lock ECU (No. 2 4 wheel drive control ECU) connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C26 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-28 (EXI3) - T31-2
Always
Below 1 Ω
S35-28 (EXI3) - C26-9
Always
Below 1 Ω
S35-28 (EXI3) - F23-1 (RLP)
Always
Below 1 Ω
S35-28 (EXI3) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. INSPECT DIFFERENTIAL LOCK SYSTEM |
Inspect rear differential lock system (Click here).
|
|
||||
| OK | |
| 9. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON / OFF
Observe the combination meter.
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.
ABS/VSC/TRC Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light /
ON or OFF
ON: ABS warning light on
OFF: ABS warning light off
-
Result Result
Proceed to
Data List Display
Data List Display When Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
for LHD
A
Does not change between ON and OFF
for RHD
B
Changes between ON and OFF
C
OFF
Does not change between ON and OFF
for LHD
A
Does not change between ON and OFF
for RHD
B
Changes between ON and OFF
C
|
|
||||
|
|
||||
| A | ||
| ||
