2014 Hilux · Service Manual BRAKE

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:
  1. The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and the skid control ECU.
  4. The anti-lock brake system is defective.
  5. w/ Rear Differential Lock:
    The rear differential is locked.

WIRING DIAGRAM

C243372E03

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Check if DTCs for the ABS are output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. C199357E58
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the C25 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-10 (WA) - C25-38
    Always
    Below 1 Ω
    S35-10 (WA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK TERMINAL VOLTAGE (EXI3 TERMINAL)

  1. C199357E62
    Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-28 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])
    Result 
    Result
    Proceed to
    NG
    w/ Rear Differential Lock
    A
    w/o Rear Differential Lock
    B
    OK
    C



B
REPAIR OR REPLACE HARNESS OR CONNECTOR

C
Go to step 9
A


7. CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL CIRCUIT)
  1. Turn the ignition switch off.

  1. Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.

  1. Disconnect the rear differential lock ECU (No. 2 4 wheel drive control ECU) connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the C26 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-28 (EXI3) - T31-2
    Always
    Below 1 Ω
    S35-28 (EXI3) - C26-9
    Always
    Below 1 Ω
    S35-28 (EXI3) - F23-1 (RLP)
    Always
    Below 1 Ω
    S35-28 (EXI3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT DIFFERENTIAL LOCK SYSTEM
  1. Inspect rear differential lock system (Click here).



NG
GO TO DIFFERENTIAL SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)
OK


9. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON / OFF
    Observe the combination meter.

  1. When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light /
    ON or OFF
    ON: ABS warning light on
    OFF: ABS warning light off
    -
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display When Performing Active Test ON/OFF Operation
    ON
    Does not change between ON and OFF
    for LHD
    A
    Does not change between ON and OFF
    for RHD
    B
    Changes between ON and OFF
    C
    OFF
    Does not change between ON and OFF
    for LHD
    A
    Does not change between ON and OFF
    for RHD
    B
    Changes between ON and OFF
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← ABS Warning Light Remains ON (Aug 2013 – Jul 2014)ABS Warning Light does not Come ON (Jun 2011 – Oct 2011) →