VSC OFF Indicator Light Remains ON
Circuit diagnosis · Vehicles built Apr 2012 – Jul 2012
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
If the skid control ECU (brake actuator assembly) stores a DTC, the VSC OFF indicator light blinks in the combination meter.Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If VSC turns off, the VSC OFF indicator light will come on.
for 4WD:
When the transfer position is L4, VSC is prohibited and the VSC OFF indicator and slip indicator lights turn on.
w/ Rear Differential Lock:
When the rear differential is locked, VSC is prohibited, and the VSC OFF indicator and slip indicator lights turn on.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- for 4WD:
As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first (Click here).
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- for 4WD:
| 1. CHECK FOR DTC |
Check if DTCs for the VSC are output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 2. CHECK TERMINAL VOLTAGE (EXI3 TERMINAL) |
Turn the ignition switch off.

Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S35-28 (EXI3) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
Result Result
Proceed to
NG
w/ Rear Differential Lock
A
w/o Rear Differential Lock
B
OK
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL CIRCUIT) |
Turn the ignition switch off.
Disconnect the rear differential lock position switch (No. 4 transfer indicator switch) connector.
Disconnect the rear differential lock ECU (No. 2 4 wheel drive control ECU) connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C26 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-28 (EXI3) - T31-2
Always
Below 1 Ω
S35-28 (EXI3) - C26-9
Always
Below 1 Ω
S35-28 (EXI3) - F23-1 (RLP)
Always
Below 1 Ω
S35-28 (EXI3) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. INSPECT REAR DIFFERENTIAL LOCK SYSTEM |
Inspect rear differential lock system (Click here).
|
|
||||
| OK | |
| 5. READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
TRC/VSC Off Mode
VSC OFF switch / Normal, Unknown, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Check that the mode display changes according to VSC OFF switch operation.
- OK:
- The intelligent tester display changes according to VSC OFF switch operation.
|
|
||||
| OK | |
| 6. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
VSC Warning Light
VSC OFF indicator light
Indicator light ON / OFF
Observe the combination meter.
When performing the VSC Warning Light Active Test, check VSC Warning Light in the Data List.
ABS/VSC/TRC Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
VSC Warning Light
VSC OFF indicator light / ON or OFF
ON: VSC OFF indicator light on
OFF: VSC OFF indicator light off
-
Result Result
Proceed to
Data List Display
Data List Display When Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
for LHD
A
Does not change between ON and OFF
for RHD
B
Changes between ON and OFF
C
OFF
Does not change between ON and OFF
for LHD
A
Does not change between ON and OFF
for RHD
B
Changes between ON and OFF
C
|
|
||||
|
|
||||
| A | ||
| ||
| 7. INSPECT VSC OFF SWITCH |
Turn the ignition switch off.
Remove the VSC OFF switch (Click here).
Inspect the VSC OFF switch (Click here).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH) |
Turn the ignition switch off.
Disconnect the VSC OFF switch connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-30 (CSW) - V8-3
Always
Below 1 Ω
S35-30 (CSW) - Body ground
Always
10 kΩ or higher
V8-4 - Body ground
Always
Below 1 Ω
Result Result
Proceed to
NG
A
OK
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C26 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-15 (VSCW) - C26-16
Always
Below 1 Ω
S35-15 (VSCW) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
