2014 Hilux · Service Manual BODY ELECTRICAL

OPERATION CHECK

Troubleshooting · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


CHECK PANEL & STEERING SWITCH

HINT:
  1. The radio and display receiver assembly panel switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.
  3. Some of the following functions may also differ from the actual vehicle depending on the device settings and options.

  1. Enter diagnostic mode (Click here).

  2. E221996
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E221999
    Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

  4. Panel & Steering Switch Check Mode

    1. E219355E01
      Operate each switch and check that the number of switches pushed and the switch conditions are correctly displayed.
      Screen Description 
      Display
      Content
      *1: Switch condition
      "Pushed" is displayed when any switch is pushed
      *2: Number of pushed switch
      1. Number of switches pushed at once
      2. If more than 3 switches are pushed at once, "More than 3" is displayed
      *3: Rotary switch direction
      Direction of rotary switch is displayed


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E221996
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E222006
    Select "Touch Switch" from the "Function Check/Setting I" screen.

  4. E176521
    Touch Switch Check

    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MIC & VOICE RECOGNITION

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E221996
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E222012
    Select "Mic & Voice Recognition" from the "Function Check/Setting I" screen.

  4. Microphone & Voice Recognition Check

    1. E222013
      When speaking into the microphone, check that the microphone input level meter changes according to the input level.


CHECK COLOR BAR

HINT:
  1. The display color on the screen is checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E221996
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E222014
    Select "Color Bar" from the "Function Check/Setting I" screen.

  4. Color Bar Check Mode

    1. E222015
      Select a color bar from the "Color Bar Check Mode" screen.

    2. Check the display color.

      HINT:
      1. The entire screen turns to the color or stripe selected.
      2. Touching the display returns to the "Color Bar Check" screen.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E221996
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E222017
    Select "Vehicle Signal" from the "Function Check/Setting I" screen.

  4. Vehicle Signal Check Mode

    1. E222021
      When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

      HINT:
      1. Only conditions having inputs are displayed.
      2. This screen displays vehicle signals input to the radio and display receiver assembly.
      3. For details of this function, refer to Diagnosis Display Detailed Description in System Description (Click here).


CHECK HANDSFREE VOICE QUALITY SETTING

HINT:
  1. The handsfree volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E221996
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E222022
    Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

  4. Receive/Send Voice Level adjustment

    NOTICE:
    Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the received voice quality is still acceptable after changing this setting.


    1. If the voice level is low, press "+" button, and if the voice level is loud, press "-" button.

      HINT:
      1. Each voice level setting is reflected when going back to the normal mode.
      2. The changing voice level ranges from -5 to +5.
      3. The initial level is "0".

  5. Voice Quality Type Adjustment

    1. C240227E01
      When changing the settings, use the number pad on the screen and input the voice quality type according to the chart below.
      Text in Illustration 
      *a
      Numeric keypad
      *b
      Setting button
      *c
      Reset button
      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type (FUJITSU TEN)
      Voice Quality Type (Pioneer)
      Voice Quality Type (Panasonic)
      Effect of Changing Voice Quality Parameter
      Adverse Effect of Changing Voice Quality Parameter
      Echo
      The other party hears their own voice echoed back to a large degree.
      1. 1000
      2. 2000
      1. 0001
      2. 0002
      3. 0003
      4. 0004
      5. 0005
      0001
      The amount that the other party hears their own voice echoed back is reduced.
      When both parties speak at the same time, the voice heard by the other party suddenly becomes quiet, cuts out, etc.
      Half Duplex
      When both parties speak at the same time, the voice heard by the other party suddenly becomes quiet, cuts out, etc.
      1. 0100
      2. 0200
      1. 0010
      2. 0020
      3. 0030
      4. 0040
      5. 0050
      0002
      The phenomenon in which the voice heard by the other party suddenly becomes quiet, cuts out, etc. when both parties speak at the same time is reduced.
      The amount that the other party hears their own voice echoed back increases.
      Noise
      A large amount of noise, such as vehicle or road noise, is mixed together with the voice heard by the other party.
      1. 0010
      2. 0020
      1. 0100
      2. 0200
      3. 0300
      4. 0400
      5. 0500
      0004
      The amount of noise, such as vehicle or road noise, that is mixed together with the voice heard by the other party is reduced.
      The quality of the voice heard by the other party worsens.
      Quality
      The quality of the voice heard by the other party is bad.
      1. 0001
      2. 0002
      1. 1000
      2. 2000
      3. 3000
      4. 4000
      5. 5000
      0003
      The quality of the voice heard by the other party improves.
      The amount of noise, such vehicle or road noise, that is mixed together with the voice heard by the other party increases.

      HINT:
      1. Refer to the "Unit Version Information" screen for information regarding the manufacturer of the radio and display receiver assembly (Click here).
      2. Voice Quality Type Adjustment can only be used to adjust the quality of the voice heard by the other party. It cannot be used to adjust the quality of the voice heard by the user.
      3. The default value is 0000.
      4. Any changes to settings are applied when the display returns to the normal screen.
      5. For cases where there is more than one value, selecting a larger value increases the effect, but the adverse effects also increase.
      6. If a value not listed in the chart is entered, the change may not be applied, or the desired effect may not be achieved.
      7. If voice quality worsens as a result of changing the settings, press the "INIT" switch and return the value to 0000.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Aug 2013)OPERATION CHECK (from Aug 2013) →