2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER
(Click here)

3. CHECK INJECTOR COMPENSATION CODE

HINT:
If the injector compensation code is not correctly registered, it may cause malfunctions.

  1. Read the injector compensation code (Click here).

  1. Check that the compensation code of the installed injector is the same as the code registered in the ECM. If the code is not the same, register the injector compensation code on the injector (Click here).


4. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A252273
    Remove the bolt, nut and 2 No. 2 injection pipe clamps.

  1. A252274
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


5. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A252275E01
    Detach the wire harness clamp.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    Wiring Harness Clamp Bracket

  1. Remove the bolt and wiring harness clamp bracket.


6. REMOVE NO. 2 FUEL PIPE

  1. A252279
    Using a 6 mm hexagon wrench, remove the supply pump hollow screw and gasket.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Supply Pump Hollow Screw
    V100137
    Fuel Check Valve
    V100138
    Union Bolt

  1. Remove the fuel check valve, union bolt and 2 gaskets.

  1. Remove the 3 bolts and No. 2 fuel pipe.


7. REMOVE NO. 3 NOZZLE LEAKAGE PIPE

  1. A252280
    Disconnect the 3 fuel hoses.
    Text in Illustration 
    V100136
    Fuel Check Valve

  1. Remove the 2 bolts.

  1. Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.


8. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A252281
    Remove the 2 bolts.
    Text in Illustration 
    V100136
    Union Bolt

  1. Remove the union bolt, gasket and No. 2 nozzle leakage pipe.


9. REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A252282
    Remove the 3 bolts and No. 2 cylinder head cover.


10. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.

  1. A223193
    Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


11. REMOVE INJECTOR ASSEMBLY

  1. A076779E04
    Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A076780E02
    Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.

← REMOVAL (Aug 2012 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →