2014 Hilux · Service Manual BODY ELECTRICAL

B15C3 Speaker Output Short

Diagnostic trouble codes · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.
DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Radio and display receiver assembly
  3. Harness or connector

WIRING DIAGRAM

E285155E01

INSPECTION PROCEDURE

HINT:
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for T-connect.


1. CHECK FOR DTC
  1. Disconnect the R22 (for 6 Speakers) and R23 radio and display receiver assembly connectors.

  1. Clear the DTCs (Click here).

  1. Check if DTC B15C3 is output (Click here).

    OK:
    DTC B15C3 is not output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2. CHECK FOR DTC
  1. Reconnect the R23 radio and display receiver assembly connector.

  1. Clear the DTC (Click here).

  1. Check if DTC B15C3 is output (Click here).

    OK:
    DTC B15C3 is not output.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area (for 6 Speakers)
    B



B
Go to step 6
A


3. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

  1. for 6 Speakers:Disconnect the T24*1 and/or T23*2 front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side (for 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-1 (FR+) - T24-4
    Always
    Below 1 Ω
    R23-5 (FR-) - T24-2
    Always
    Below 1 Ω
    T24-3 - S16-1
    Always
    Below 1 Ω
    T24-1 - S16-2
    Always
    Below 1 Ω
    R23-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R23-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1) - Body ground
    Always
    10 kΩ or higher
    for LH Side (for 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-2 (FL+) - T23-4
    Always
    Below 1 Ω
    R23-6 (FL-) - T23-2
    Always
    Below 1 Ω
    T23-3 - S15-1
    Always
    Below 1 Ω
    T23-1 - S15-2
    Always
    Below 1 Ω
    R23-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R23-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    T23-3 - Body ground
    Always
    10 kΩ or higher
    T23-1 - Body ground
    Always
    10 kΩ or higher
    for RH Side (except 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-1 (FR+) - S16-1
    Always
    Below 1 Ω
    R23-5 (FR-) - S16-2
    Always
    Below 1 Ω
    R23-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R23-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH Side (except 6 Speakers):
    Tester Connection
    Condition
    Specified Condition
    R23-2 (FL+) - S15-1
    Always
    Below 1 Ω
    R23-6 (FL-) - S15-2
    Always
    Below 1 Ω
    R23-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R23-6 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

    1. *1: for RH Side
    2. *2: for LH Side

  1. Inspect the front No. 1 speaker assembly (Click here).

    Result 
    Result
    Proceed to
    OK (for 6 Speakers)
    A
    OK (except 6 Speakers)
    B
    NG
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


5. CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

6. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the R22 radio and display receiver assembly connector.

  1. for Double Cab:

    1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

  1. for Extra Cab:

    1. Disconnect the S20*1 and/or S19*2 rear speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Double Cab RH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R22-3 (RR-) - S18-2
    Always
    Below 1 Ω
    R22-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R22-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for Double Cab LH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R22-6 (RL-) - S17-2
    Always
    Below 1 Ω
    R22-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R22-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    for Extra Cab RH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-1 (RR+) - S20-1
    Always
    Below 1 Ω
    R22-3 (RR-) - S20-2
    Always
    Below 1 Ω
    R22-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R22-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    except Extra Cab LH Side 
    Tester Connection
    Condition
    Specified Condition
    R22-2 (RL+) - S19-1
    Always
    Below 1 Ω
    R22-6 (RL-) - S19-2
    Always
    Below 1 Ω
    R22-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R22-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT REAR SPEAKER ASSEMBLY
  1. *1: for RH Side
  2. *2: for LH Side
  1. for Double Cab:

    1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

  1. for Extra Cab:

    1. Disconnect the S20*1 and/or S19*2 rear speaker assembly connector.

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)


← B15C3 Speaker Output Short (Aug 2012 – Jul 2013)Noise Occurs (Jun 2011 – Jul 2012) →