2014 Hilux · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL FRONT SIDE STEP PLATE COVER LH
  1. Attach the claw to install the front side step plate cover.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }


2. INSTALL REAR SIDE STEP PLATE COVER LH
  1. Attach the claw to install the rear side step plate cover.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }


3. INSTALL NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH
  1. Install a nose piece to an air riveter or hand riveter.

  1. Insert the mandrel part of a new rivet into the nose piece.

  1. B277511
    Using the riveter, install the No. 1 side step stay with the 2 rivets as shown in the illustration.

    HINT:
    If the rivet cannot be cut, pull it once and cut it.

    NOTICE:

    1. B171664E15
      Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *1
      Riveter
      *2
      Mandrel
      *a
      INCORRECT
      *b
      CORRECT

    2. B172390E14
      Confirm that the rivets are seated properly against the No. 1 side step stay.
    3. Do not tilt the riveter when installing the rivet to the No. 1 side step stay.
    4. Do not leave any space between the rivet head and No. 1 side step stay.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT

    5. B172391E13
      Do not leave any space between the No. 1 side step stay and step plate. Firmly hold together the 2 items while installing the rivet.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT


4. INSTALL NO. 2 SIDE STEP BRACKET LH (for Extra Cab, for Double Cab)
  1. Install a nose piece to an air riveter or hand riveter.

  1. Insert the mandrel part of a new rivet into the nose piece.

  1. B277512
    Using the riveter, install the No. 2 side step bracket with the 2 rivets as shown in the illustration.

    HINT:
    If the rivet cannot be cut, pull it once and cut it.

    NOTICE:

    1. B171664E15
      Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *1
      Riveter
      *2
      Mandrel
      *a
      INCORRECT
      *b
      CORRECT

    2. B172390E14
      Confirm that the rivets are seated properly against the No. 2 side step bracket.
    3. Do not tilt the riveter when installing the rivet to the No. 2 side step bracket.
    4. Do not leave any space between the rivet head and No. 2 side step bracket.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT

    5. B172391E13
      Do not leave any space between the No. 2 side step bracket and step plate. Firmly hold together the 2 items while installing the rivet.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT


5. INSTALL NO. 3 SIDE STEP BRACKET LH
  1. Install a nose piece to an air riveter or hand riveter.

  1. Insert the mandrel part of a new rivet into the nose piece.

  1. B277514
    Using the riveter, install the No. 3 side step bracket with the 2 rivets as shown in the illustration.

    HINT:
    If the rivet cannot be cut, pull it once and cut it.

    NOTICE:

    1. B171664E15
      Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *1
      Riveter
      *2
      Mandrel
      *a
      INCORRECT
      *b
      CORRECT

    2. B172390E14
      Confirm that the rivets are seated properly against the No. 3 side step bracket.
    3. Do not tilt the riveter when installing the rivet to the No. 3 side step bracket.
    4. Do not leave any space between the rivet head and No. 3 side step bracket.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT

    5. B172391E13
      Do not leave any space between the No. 3 side step bracket and step plate. Firmly hold together the 2 items while installing the rivet.
      Text in Illustration 
      *1
      Riveter
      *a
      INCORRECT
      *b
      CORRECT

← DISASSEMBLY (from Jun 2011)INSTALLATION (from Jun 2011) →