Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1.
INSTALL FRONT SEATBACK HEATER ASSEMBLY LH
Set the front seatback heater assembly LH on the separate type front seatback cover.
Using a tacker, install the front seatback heater assembly LH to the separate type front seatback cover with 6 new tack pins as shown in the illustration.
NOTICE:
Do not substitute other metal parts for tack pins.
Text in Illustration
*1
Tack Pin
*2
Separate Type Front Seatback Cover
*3
Listing Pocket of Separate Type Front Seatback Cover
-
-
2.
INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
*1
Hog Ring Pliers
-
-
*a
Front view of front seatback
*b
Rear view of front seatback
Attach the 4 claws to install the 2 front seat headrest supports.
Attach the separate type front seatback cover bracket and install the nut.
Torque:
5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
NOTICE:
After the separate type front seatback cover is installed, make sure the separate type front seatback cover bracket is not twisted.
Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.
Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the separate type front seatback spring assembly with new hog rings.
Text in Illustration
*1
Hog Ring Pliers
Pass the front seat airbag wire harness through the hole of the separate type front seatback cover.
Using hog ring pliers, attach the separate type front seatback cover with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the 2 pieces of fastening tape.
Text in Illustration
*1
Hog Ring Pliers
*2
Fastening Tape
3.
INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Install the separate type front seatback assembly with the 4 bolts.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
for LHD, w/ Seat Heater System: Connect the front seatback heater assembly LH connector.
Using hog ring pliers, attach the separate type front seat cushion cover and rubber bands of the separate type front seatback cover to the front seat cushion frame sub-assembly LH with new hog rings.
Text in Illustration
*1
Hog Ring Pliers
Attach the 3 front seat airbag wire harness clamps.
4.
INSTALL SEATBACK SPRING LH
Install the seatback spring LH.
5.
INSTALL FRONT SEAT CUSHION SHIELD LH
Attach the guide and 2 hooks in the order shown in the illustration to install the front seat cushion shield LH.
Text in Illustration
*1
Guide
*2
Hook
Install the 2 screws.
6.
INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
Attach the claw to install the reclining adjuster release handle LH.
7.
INSTALL FRONT SEAT INNER CUSHION SHIELD LH
Attach the 2 hooks in the order shown in the illustration to install the front seat inner cushion shield LH.
Install the 2 screws.
8.
INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)