Wear protective gloves. Sharp areas on the parts may injure your hands.
1.
INSTALL FRONT SEATBACK HEATER ASSEMBLY LH
Set the front seatback heater assembly LH on the separate type front seatback cover.
Using a tacker, install the front seatback heater assembly LH to the separate type front seatback cover with 6 new tack pins as shown in the illustration.
NOTICE:
Do not substitute other metal parts for tack pins.
Text in Illustration
*1
Tack Pin
*2
Separate Type Front Seatback Cover
*3
Listing Pocket of Separate Type Front Seatback Cover
-
-
2.
INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, attach the strap of the separate type front seatback cover to the separate type front seatback pad with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
*A
w/o Front Seat Side Airbag
*B
w/ Front Seat Side Airbag
*1
Hog Ring Pliers
-
-
*a
Front view of front seatback
*b
Rear view of front seatback
Attach the 4 claws to install the 2 front seat headrest supports.
w/ Front Seat Side Airbag: Attach the separate type front seatback cover bracket and install the nut.
Torque:
5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
NOTICE:
After the separate type front seatback cover is installed, make sure the separate type front seatback cover bracket is not twisted.
Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.
Using hog ring pliers, attach the strap of the separate type front seatback cover together with the No. 1 seatback cloth to the separate type front seatback spring assembly with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
*1
Hog Ring Pliers
for LHD, w/ Seat Heater System: Pass the front seatback heater assembly LH wire harness through the hole of the separate type front seatback cover.
Pass the No. 1 seat wire through the hole of the separate type front seatback cover.
Using hog ring pliers, attach the wires at the bottom of the separate type front seatback cover with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
*1
Hog Ring Pliers
w/o Front Seat Side Airbag: Connect the No. 1 seat wire connector and attach the wire harness clamp.
3.
INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the guide to install the reclining adjuster inside cover LH.
4.
INSTALL RECLINING ADJUSTER INSIDE COVER RH
Attach the guide to install the reclining adjuster inside cover RH.
5.
INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Install the separate type front seatback assembly with the 4 bolts.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Install the 2 screws.
Attach the front seatback heater assembly LH wire harness clamp.
Connect the No. 1 seat wire connector and attach the wire harness clamp.
Attach the 4 front seat airbag wire harness clamps.
6.
INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
Install the front seat inner belt assembly LH with the nut.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connector and attach the 3 clamps.
7.
INSTALL FRONT SEAT INNER CUSHION SHIELD LH
Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat inner cushion shield RH.
Attach the claw to temporarily install the front seat inner cushion shield RH.
NOTICE:
Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.
Attach the guide and claw.
NOTICE:
Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.
Install the screw.
8.
INSTALL FRONT SEAT CUSHION SHIELD LH
Attach the claw and guide to install the front seat cushion shield RH.
Install the 3 screws.
Install the 2 screws.
9.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Attach the 4 claws to install the slide and vertical power seat switch knob.
10.
INSTALL RECLINING POWER SEAT SWITCH KNOB
Attach the 2 claws to install the reclining power seat switch knob.