2014 Hilux · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

B284714E01
  1. Set the front seat cushion heater on the separate type front seat cushion cover.

  1. Using a tacker, install the front seat cushion heater to the separate type front seat cushion cover with 12 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.

    Text in Illustration 
    *1
    Tack Pin
    *2
    Separate Type Front Seat Cushion Cover
    *3
    Front Seat Cushion Heater Assembly LH


2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B207627E02
    Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


3. INSTALL FRONT SEAT CUSHION COVER WITH PAD
  1. Attach the hooks to install the front seat cushion cover with pad.

  1. Bend the 2 front seat cushion frame claws downward.

  1. B284719
    for LHD, w/ Seat Heater System:

    1. Attach the 4 front seat cushion heater assembly LH clamps.

    2. Connect the 2 front seat cushion heater assembly LH connectors.

  1. B207083E02
    Using hog ring pliers, attach the rubber bands of the separate type front seatback cover to the seat cushion spring with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

B284022E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect the connector and attach the 3 clamps.


5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

  1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat inner cushion shield RH.

    B278523

  1. B278521
    Attach the claw to temporarily install the front seat inner cushion shield RH.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. B278522
    Attach the guide and claw.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

  1. Install the screw.


6. INSTALL FRONT POWER SEAT SWITCH LH
  1. Connect the connector.

  1. Install the front power seat switch RH with the 3 screws.


7. INSTALL FRONT SEAT CUSHION SHIELD LH
  1. Attach the claw and guide to install the front seat cushion shield RH.

  1. Install the 3 screws.

  1. Install the 2 screws.


8. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

  1. B207446
    Attach the 4 claws to install the slide and vertical power seat switch knob.


9. INSTALL RECLINING POWER SEAT SWITCH KNOB

  1. B207447
    Attach the 2 claws to install the reclining power seat switch knob.


10. INSTALL FRONT SEAT ASSEMBLY
(Click here)

11. CHECK SRS WARNING LIGHT
(Click here)

12. INSPECT FRONT SEAT ASSEMBLY
  1. Check the seat heater operation.

    1. Turn the ignition switch to ON.

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

← INSPECTION (from Jun 2011)INSTALLATION (Aug 2012 – Jul 2013) →