Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and detects the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A208462
1.49,2 1.646,1.76 1.646,1.76 1.792,1.76 false 0.208,0.146 0.75,0.385 0.542,0.24 10 false (Fig. 1) 0.208,0.542 1.229,0.781 1.021,0.24 10 false Resistance kΩ 1.823,1.667 2.604,1.875 0.781,0.208 10 false Acceptable 1.208,4.063 2.521,4.281 1.313,0.219 10 false Temperature °C (°F)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0110 Intake Air Temperature Circuit Open or short the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Open or short in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM


- DTC stored
P0112 Intake Air Temperature Circuit Low Input Short in the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Short in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM


- DTC stored
P0113 Intake Air Temperature Circuit High Input Open in the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Open in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0110 Intake Air
P0112
P0113

HINT:
·

If DTC P0110, P0112 and/or P0113 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0110, P0112 and/or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

P0110, P0112, P0113
DTC Detection Drive Pattern Ignition switch to ON for 0.5 seconds

WIRING DIAGRAM

A255058
0.313,2.083 3.656,2.365 3.344,0.281 10 false Intake Air Temperature Sensor (Built into MAF Meter) 0.313,1.938 0.604,2.104 0.292,0.167 10 false C36 5.948,2.448 6.323,2.677 0.375,0.229 10 false ECM 1.604,0.969 1.906,1.188 0.302,0.219 10 false THA 1.719,1.542 1.906,1.76 0.188,0.219 10 false E2 5.448,0.958 5.813,1.188 0.365,0.229 10 false THA 5.448,1.552 5.729,1.729 0.281,0.177 10 false E2 5.896,0.219 6.198,0.458 0.302,0.24 10 false 5 V 6.104,0.656 6.292,0.854 0.188,0.198 10 false R 1.969,0.958 2.125,1.188 0.156,0.229 10 false 4 1.969,1.542 2.135,1.76 0.167,0.219 10 false 5 5.948,2.313 6.313,2.521 0.365,0.208 10 false C22 5.219,0.958 5.438,1.198 0.219,0.24 10 false 31 5.219,1.552 5.458,1.74 0.24,0.188 10 false 28 0.073,0.063 1.188,0.323 1.115,0.26 10 false w/ MAF meter

A255058
0.313,2.083 3.635,2.26 3.323,0.177 10 false Intake Air Temperature Sensor 0.313,1.938 0.604,2.104 0.292,0.167 10 false C91 5.927,2.469 6.302,2.635 0.375,0.167 10 false ECM 1.604,0.979 1.927,1.146 0.323,0.167 10 false THA 1.698,1.542 1.917,1.708 0.219,0.167 10 false E2 5.448,0.979 5.771,1.146 0.323,0.167 10 false THA 5.448,1.573 5.667,1.74 0.219,0.167 10 false E2 5.896,0.24 6.167,0.406 0.271,0.167 10 false 5 V 6.104,0.667 6.271,0.833 0.167,0.167 10 false R 1.969,0.979 2.094,1.135 0.125,0.156 10 false 2 1.969,1.542 2.094,1.708 0.125,0.167 10 false 1 5.948,2.313 6.26,2.479 0.313,0.167 10 false C22 5.188,0.979 5.375,1.135 0.188,0.156 10 false 31 5.198,1.573 5.385,1.729 0.188,0.156 10 false 28 0.073,0.063 1.51,0.24 1.438,0.177 10 false w/o MAF meter

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

OK:

Same as actual intake air temperature


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A114039
0.5,3.51 0.906,3.75 0.406,0.24 2.719,0.323 2.938,0.531 0.219,0.208 10 false *2 2.479,1.156 2.844,1.354 0.365,0.198 10 false THA 2.479,1.531 2.708,1.729 0.229,0.198 10 false E2 0.385,2.76 0.573,2.958 0.188,0.198 10 false *a 0.552,3.542 0.854,3.719 0.302,0.177 10 false C36 0.385,0.344 0.594,0.552 0.208,0.208 10 false *1
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


A303339
0.469,3.521 0.896,3.792 0.427,0.271 1.198,4.104 1.469,3.74 false 2.219,4.094 1.958,3.729 false 0.323,0.438 0.635,0.635 0.313,0.198 10 false *1 2.76,0.354 3.073,0.552 0.313,0.198 10 false *2 2.448,1.156 2.854,1.354 0.406,0.198 10 false THA 2.458,1.521 2.771,1.719 0.313,0.198 10 false E2 0.396,2.625 0.708,2.823 0.313,0.198 10 false *a 1.073,4.167 1.385,4.365 0.313,0.198 10 false E2 2.146,4.156 2.604,4.354 0.458,0.198 10 false THA 0.563,3.583 0.958,3.844 0.396,0.26 10 false C91
*1 Intake Air Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor)


w/ mass air flow meter:

i.

Disconnect the C36 mass air flow meter connector.


ii.

Connect terminals 4 and 5 of the mass air flow meter wire harness side connector.


iii.

Connect the intelligent tester to the DLC3.


iv.

Turn the ignition switch ON and turn the intelligent tester ON.


v.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

vi.

Read the values.

OK:

140°C (284°F) or more



vii.

Reconnect the mass air flow meter connector.



b.

w/o mass air flow meter:

i.

Disconnect the C91 intake air temperature sensor connector.


ii.

Connect terminals 1 and 2 of the intake air temperature sensor wire harness side connector.


iii.

Connect the intelligent tester to the DLC3.


iv.

Turn the ignition switch ON and turn the intelligent tester ON.


v.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

vi.

Read the values.

OK:

140°C (284°F) or more



vii.

Reconnect the intake air temperature sensor connector.



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the mass air flow meter (w/ mass air flow meter).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/o DPF)>REMOVAL


b.

Replace the intake air temperature sensor (w/o mass air flow meter).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

w/ mass air flow meter:

i.

Disconnect the mass air flow meter connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ mass air flow meter
Tester Connection Condition Specified Condition
C36-4 (THA) - C22-31 (THA) Always Below 1 Ω
C36-5 (E2) - C22-28 (E2) Always Below 1 Ω



iv.

Reconnect the mass air flow meter connector.


v.

Reconnect the ECM connector.



b.

w/o mass air flow meter:

i.

Disconnect the intake air temperature sensor connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

w/o mass air flow meter
Tester Connection Condition Specified Condition
C91-2 (THA) - C22-31 (THA) Always Below 1 Ω
C91-1 (E2) - C22-28 (E2) Always Below 1 Ω


iv.

Reconnect the intake air temperature sensor connector.


v.

Reconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633
2.479,1.146 2.813,1.344 0.333,0.198 10 false THA 2.438,1.5 2.729,1.76 0.292,0.26 10 false E2 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Mass Air Flow Meter
*2 ECM


w/ mass air flow meter:

i.

Disconnect the mass air flow meter connector.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON and turn the tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

v.

Read the value.

OK:

-40°C (-40°F)



vi.

Reconnect the mass air flow meter connector.



b.
A302633
2.479,1.146 2.813,1.344 0.333,0.198 10 false THA 2.438,1.5 2.729,1.76 0.292,0.26 10 false E2 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Intake Air Temperature Sensor
*2 ECM


w/o mass air flow meter:

i.

Disconnect the intake air temperature sensor connector.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the ignition switch to ON and turn the tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

v.

Read the value.

OK:

-40°C (-40°F)



vi.

Reconnect the intake air temperature sensor connector.



Result:
Proceed to
OK
NG



OK

7.REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
7.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the mass air flow meter (w/ mass air flow meter).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/o DPF)>REMOVAL


b.

Replace the intake air temperature sensor (w/o mass air flow meter).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

w/ mass air flow meter:

i.

Disconnect the mass air flow meter connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ mass air flow meter
Tester Connection Condition Specified Condition
C36-4 (THA) or C22-31 (THA) - Body ground Always 10 kΩ or higher



iv.

Reconnect the mass air flow meter connector.


v.

Reconnect the ECM connector.



b.

w/o mass air flow meter:

i.

Disconnect the intake air temperature sensor connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

w/o mass air flow meter
Tester Connection Condition Specified Condition
C91-1 (THA) or C22-31 (THA) - Body ground Always 10 kΩ or higher


iv.

Reconnect the intake air temperature sensor connector.


v.

Reconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED