Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P2120).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic).
·

Accelerator pedal position sensor circuit

·

Accelerator pedal position sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2121
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %



CONFIRMATION DRIVING PATTERN

P2121
DTC Detection Drive Pattern Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds



CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)
a.
C129061
0.833,1.688 1.042,1.896 0.208,0.208 10 false *a 0.271,0.396 0.479,0.604 0.208,0.208 10 false *1 2.24,1.688 2.5,1.896 0.26,0.208 10 false *b
*1 Accelerator Pedal Assembly
*a Depressed
*b Released


Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the values.

Standard Voltage:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%


Result:
Proceed to
OK
NG




OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-1 (VCP2) - G39-27 (VCP2) Always Below 1 Ω
G6-2 (EPA2) - G39-29 (EPA2) Always Below 1 Ω
G6-3 (VPA2) - G39-23 (VPA2) Always Below 1 Ω
G6-4 (VCPA) - G39-26 (VCPA) Always Below 1 Ω
G6-5 (EPA) - G39-28 (EPA) Always Below 1 Ω
G6-6 (VPA) - G39-22 (VPA) Always Below 1 Ω
G6-1 (VCP2) or G39-27 (VCP2) - Body ground Always 10 kΩ or higher
G6-2 (EPA2) or G39-29 (EPA2) - Body ground Always 10 kΩ or higher
G6-3 (VPA2) or G39-23 (VPA2) - Body ground Always 10 kΩ or higher
G6-4 (VCPA) or G39-26 (VCPA) - Body ground Always 10 kΩ or higher
G6-5 (EPA) or G39-28 (EPA) - Body ground Always 10 kΩ or higher
G6-6 (VPA) or G39-22 (VPA) - Body ground Always 10 kΩ or higher



d.

Reconnect the accelerator pedal position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON.


d.

Fully release the accelerator pedal for 3 seconds or more, depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Result Proceed to
P2121 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Fully release the accelerator pedal for 3 seconds or more, depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END