Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) J

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK INJECTOR DRIVER (POWER SOURCE)
a.

Disconnect the injector driver connectors.


b.
A221614
0.51,1.271 0.896,1.531 0.385,0.26 1.677,1.188 1.156,0.844 true 2.438,1.635 1.979,1.25 true 0.573,1.323 0.875,1.542 0.302,0.219 10 false C43 0.719,0.719 1.208,0.979 0.49,0.26 10 false +B (+) 0.104,0.156 0.333,0.365 0.229,0.208 10 false *a 2.479,1.667 3.073,1.906 0.594,0.24 10 false GND (-)
*a Front view of wire harness connector
(to Injector Driver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C43-2 (+B) - C43-3 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the injector driver connector.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS

NG

2.INSPECT NO. 1 INTEGRATION RELAY (EDU)
2.INSPECT NO. 1 INTEGRATION RELAY (EDU)
a.

Inspect the No. 1 integration relay (EDU).

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY [EDU] - INJECTOR DRIVER)

NG

REPLACE NO. 1 INTEGRATION RELAY (EDU)

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY [EDU] - INJECTOR DRIVER)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the injector driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C43-2 (+B) - 1J-8 Always Below 1 Ω
C43-3 (GND) - Body ground Always Below 1 Ω
C43-2 (+B) or 1J-8 - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver connector.


e.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G39-10 (IREL) - 1J-7 Always Below 1 Ω
G39-10 (IREL) or 1J-7 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR