The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0122 | Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input | Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open or short in VLU circuit ·
Open in VC circuit ·
ECM |
Comes on | DTC stored |
| P0123 | Throttle / Pedal Position Sensor / Switch "A" Circuit High Input | Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic). | ·
Throttle position sensor ·
Open in E2 circuit ·
VC and VLU circuits are short-circuited ·
ECM |
Comes on | DTC stored |
If DTC P0122 and/or P0123 is stored, the following symptoms may appear:
- Intake booming noise
- Black smoke
- Lack of power
- Vibration at engine stop
- Turbo overspeed, turbo damage
| DTC Detection Drive Pattern | Ignition switch to ON for 3 seconds |
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the throttle position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C9-1 (VC) - C22-18 (VC) | Always | Below 1 Ω |
| C9-3 (VTA) - C23-29 (VLU) | Always | Below 1 Ω |
| C9-2 (E2) - C22-28 (E2) | Always | Below 1 Ω |
| C9-1 (VC) or C22-18 (VC) - Body ground | Always | 10 kΩ or higher |
| C9-3 (VTA) or C23-29 (VLU) - Body ground | Always | 10 kΩ or higher |
| C9-2 (E2) or C22-28 (E2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle position sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Throttle Position Sensor) |
Disconnect the throttle position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C9-1 (VC) - C9-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
Reconnect the throttle position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY(w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle position.
| Tester Display |
|---|
| Actual Throttle Position |
Check the movement of the throttle valve when idling the engine after starting it from ignition switch to ON.
| Condition | Tester Display |
|---|---|
| Ignition switch ON | -5 to 5% |
| Idling | 0 to 90% |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT