Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052067 ECD SYSTEM(w/ EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch to ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

P0504
DTC Detection Drive Pattern Depress and release brake pedal with ignition switch to ON

WIRING DIAGRAM

A154326
0.719,1.333 0.979,1.5 0.26,0.167 10 false G9 0.719,1.49 1.656,1.719 0.938,0.229 10 false Ignition Switch 4.25,1.938 4.563,2.135 0.313,0.198 10 false A24 4.26,2.083 5.417,2.333 1.156,0.25 10 false Stop Light Switch 0.677,1.031 0.813,1.198 0.135,0.167 10 false 5 1.656,1.031 1.792,1.198 0.135,0.167 10 false 6 4.25,1.031 4.385,1.198 0.135,0.167 10 false 3 4.25,1.625 4.385,1.792 0.135,0.167 10 false 2 5.281,1.031 5.417,1.198 0.135,0.167 10 false 4 5.281,1.625 5.417,1.792 0.135,0.167 10 false 1 0.854,1.031 1.281,1.281 0.427,0.25 10 false AM2 0.885,2.719 1.198,2.885 0.313,0.167 10 false AM2 2.323,1.698 2.635,1.865 0.313,0.167 10 false ALT 2.896,1.063 3.208,1.229 0.313,0.167 10 false IGN 3.427,1.667 3.854,1.833 0.427,0.167 10 false STOP 1.354,1.031 1.656,1.24 0.302,0.208 10 false IG2 6.302,3.469 6.688,3.677 0.385,0.208 10 false ECM 5.927,0.719 6.125,0.896 0.198,0.177 10 false 14 5.854,0.917 6.177,1.094 0.323,0.177 10 false G38 6.219,0.896 6.677,1.188 0.458,0.292 10 false ST1- 5.927,1.323 6.125,1.5 0.198,0.177 10 false 15 5.854,1.521 6.198,1.698 0.344,0.177 10 false G38 6.219,1.5 6.708,1.76 0.49,0.26 10 false STP 5.969,2.313 6.125,2.49 0.156,0.177 10 false 7 5.865,2.51 6.198,2.688 0.333,0.177 10 false C23 6.219,2.5 6.521,2.75 0.302,0.25 10 false E1 3.844,2.99 4.354,3.198 0.51,0.208 10 false Battery

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
A253393
0.719,1.083 1.104,1.302 0.385,0.219 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.781,1.104 1.083,1.302 0.302,0.198 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V
A24-3 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

5.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106
1.938,2.531 2.354,2.792 0.417,0.26 1.552,3.938 1.927,3.177 true 2.333,3.906 1.979,3.177 true 0.177,0.073 0.49,0.271 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 2,2.573 2.313,2.771 0.313,0.198 10 false G38 1.292,3.948 1.896,4.198 0.604,0.25 10 false 15 (STP) 2.271,3.948 2.896,4.198 0.625,0.25 10 false 14 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G38-14 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
G38-15 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END