This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0724 | Brake Switch "B" Circuit High | Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times (2 trip detection logic). | ·
Short in stop light switch signal circuit ·
Stop light switch assembly ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0724 | Stop Light Switch |
| DTC Detection Drive Pattern | Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times. |
Refer to DTC P0504 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0504).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
| Tester Display |
|---|
| Stop Light Switch |
Read the value displayed on the tester when the brake pedal is depressed and released.
| Brake Pedal | Display |
|---|---|
| Released | OFF |
| Depressed | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Brake Pedal Depressed |
| *b | Brake Pedal Released |
| *c | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Condition | Specified Condition |
|---|---|---|
| G149-8 (STP) - Body ground | Released | 0 to 3 V |
| Depressed | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV FUEL>COMMON RAIL(w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0724.
Check that STATUS is NORMAL.
If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.
If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.
| Proceed to |
|---|
| NEXT |
NEXT