Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2454  Diesel Particulate Filter Pressure Sensor "A" Circuit Low  P2455  Diesel Particulate Filter Pressure Sensor "A" Circuit High  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P2454 and/or P2455 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



A128654
4.417,1.208 4.229,1.438 false 4.594,1.125 4.729,1.375 false 4.406,1.167 4.219,1.24 false 5.333,3.094 5.104,2.604 5.104,2.604 5.146,2.604 false 1.302,2.219 0.792,2.969 false 2.75,2.552 2.885,2.969 false 1.302,0.75 2.177,0.969 0.875,0.219 10 false Exhaust Gas 2.917,0.74 3.313,0.938 0.396,0.198 10 false ECM 0.375,2.99 1.24,3.458 0.865,0.469 10 false DPF Catalytic Converter 2.344,2.99 3.583,3.396 1.24,0.406 10 false Differential Pressure Sensor 3.854,0.104 5.802,0.417 1.948,0.313 10 false Property of Output Voltage: 4.76,1.313 5.677,1.531 0.917,0.219 10 false Stores P2455 5.167,2.521 6.094,2.729 0.927,0.208 10 false Stores P2454 4.052,0.688 6.135,0.958 2.083,0.271 10 false Differential Pressure Voltage (V) 4.021,0.969 4.427,1.177 0.406,0.208 10 false 5.000 3.865,1.167 4.281,1.375 0.417,0.208 10 false 4.800 3.865,1.365 4.271,1.552 0.406,0.188 10 false 4.650 4.021,2.385 4.406,2.594 0.385,0.208 10 false 1.530 4.021,2.604 4.427,2.813 0.406,0.208 10 false 0.750 4.021,2.76 4.427,2.969 0.406,0.208 10 false 0.555 4.021,2.906 4.458,3.135 0.438,0.229 10 false 0.400 4.292,3.156 4.458,3.344 0.167,0.188 10 false 0 4.771,3.24 4.917,3.438 0.146,0.198 10 false 0 4.531,3.24 4.76,3.458 0.229,0.219 10 false -5 4.938,3.24 5.26,3.427 0.323,0.188 10 false 20.0 6.469,3.229 6.885,3.417 0.417,0.188 10 false 100.0 4.333,3.458 6.865,3.719 2.531,0.26 10 false Exhaust Gas Differential Pressure (kPa)

The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference in pressure exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P2454 or P2455, and illuminates the MIL.

HINT:

If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2454 Diesel Particulate Filter Pressure Sensor "A" Circuit Low differential pressure sensor assembly output voltage is below 0.4 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect Differential pressure sensor Assembly hose routing

·

Differential pressure sensor Assembly

·

ECM


Comes on DTC stored
P2455 Diesel Particulate Filter Pressure Sensor "A" Circuit High differential pressure sensor assembly output voltage is higher than 4.8 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect Differential pressure sensor Assembly hose routing

·

Differential pressure sensor Assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2454 DPF Differential Pressure
P2455

HINT:
·

DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range / Performance) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor assembly.

·

After confirming DTC P2454 and P2455, check the differential pressure in the "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" menu using the intelligent tester.


Reference:
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


CONFIRMATION DRIVING PATTERN

P2454, P2455
DTC Detection Drive Pattern Ignition switch ON for 5 seconds

MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A165731
0.385,2.229 2.177,2.5 1.792,0.271 10 false Differential Pressure Sensor 6.052,2.271 6.5,2.51 0.448,0.24 10 false ECM 1.49,1.573 1.708,1.771 0.219,0.198 10 false E2 1.49,1.052 1.75,1.25 0.26,0.198 10 false VC 1.417,0.469 1.792,0.646 0.375,0.177 10 false PEX 5.698,1.583 5.948,1.771 0.25,0.188 10 false E2 5.698,1.031 5.969,1.219 0.271,0.188 10 false VC 5.698,0.469 6.021,0.677 0.323,0.208 10 false PEX 1.854,1.458 1.979,1.635 0.125,0.177 10 false 1 1.854,0.354 1.969,0.531 0.115,0.177 10 false 2 1.844,0.917 1.969,1.094 0.125,0.177 10 false 3 5.458,0.365 5.646,0.542 0.188,0.177 10 false 7 5.406,0.927 5.635,1.135 0.229,0.208 10 false 13 5.417,1.469 5.646,1.677 0.229,0.208 10 false 14 6.031,2.031 6.458,2.219 0.427,0.188 10 false C114 0.354,2.052 0.729,2.229 0.375,0.177 10 false C125

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WIRE HARNESS (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
a.

Disconnect the differential pressure sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C125-2 (PEX) - C114-7 (PEX) Always Below 1 Ω
C125-3 (VC) - C114-13 (VC) Always Below 1 Ω
C125-1 (E2) - C114-14 (E2) Always Below 1 Ω
C125-2 (PEX) or C114-7 (PEX) - Body ground Always 10 kΩ or higher
C125-3 (VC) or C114-13 (VC) - Body ground Always 10 kΩ or higher



d.

Reconnect the differential pressure sensor assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (VC)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (VC)
a.
A204467
0.583,1.104 0.99,1.344 0.406,0.24 2.292,1.646 1.948,1.271 true 0.448,0.427 0.76,0.625 0.313,0.198 10 false *a 0.615,1.146 1.031,1.365 0.417,0.219 10 false C125 2.313,1.635 2.625,1.833 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Differential Pressure Sensor Assembly)


Disconnect the differential pressure sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C125-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

4.REPLACE ECM
3.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Replace the differential pressure sensor assembly.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON and wait for 5 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END